Results 1 to 10 of 10
  1. #1
    Field Supervisor 500+ Posts
    MX-FN27 inner finisher problems


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    MX-FN27 inner finisher problems

    Hello, I am working on a 3050N with fn-27 inner finisher and PN-14 hole punch. Customer is hole punching and stapling. The problem is on about 3 sets out of 10 the first page out does not coma back all the way6 and gets missed when stapling. It is off by about a quarter inch. It is always the first sheet out that does not get stapled. The machine is pretty new,I have tried cleaning the band rollers and rubber flappers ect but no difference. Hope someone else has suggestions or has seen this problem. Thanks for any help

  2. #2
    Senior Tech 250+ Posts driving lots of miles's Avatar
    Join Date
    Jun 2016
    Location
    Kansas
    Posts
    362
    Rep Power
    22

    Re: MX-FN27 inner finisher problems

    I would clean again or replace the rubber flappers and also check the discharge tray and make sure it does not have any residue on it.

  3. #3
    Senior Tech 250+ Posts
    MX-FN27 inner finisher problems


    Join Date
    Oct 2008
    Location
    Manchester, NH
    Posts
    459
    Rep Power
    37

    Re: MX-FN27 inner finisher problems

    Different finisher, but same series of copiers. Check for static.

  4. #4
    Senior Tech 250+ Posts
    MX-FN27 inner finisher problems

    Tech2002's Avatar
    Join Date
    Aug 2008
    Location
    Hartford, CT
    Posts
    327
    Rep Power
    35

    Re: MX-FN27 inner finisher problems

    Quote Originally Posted by Hansen88 View Post
    Hello, I am working on a 3050N with fn-27 inner finisher and PN-14 hole punch. Customer is hole punching and stapling. The problem is on about 3 sets out of 10 the first page out does not coma back all the way6 and gets missed when stapling. It is off by about a quarter inch. It is always the first sheet out that does not get stapled. The machine is pretty new,I have tried cleaning the band rollers and rubber flappers ect but no difference. Hope someone else has suggestions or has seen this problem. Thanks for any help
    Agree with Trusted Tech. If the Unit is fairly new I have had issues with the feeds. I have used a Rubber rejuvenator spray depending how deep a cleaning they may need. Some times it's the paper too. Paper is cheaply made today and is full of moisture.

  5. #5
    Field Supervisor 500+ Posts
    MX-FN27 inner finisher problems


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    Re: MX-FN27 inner finisher problems

    Thanks guys, I installed the latest firmware and cleaned the paper path of the finnisher with anti static spray. It didnt do the problem anymore while I was there so I guess Ill see if customer calls back or not. It seems good though.

  6. #6
    The Wolf 2,500+ Posts mojorolla's Avatar
    Join Date
    Jan 2010
    Location
    Cleveland OH
    Posts
    2,512
    Rep Power
    125

    Re: MX-FN27 inner finisher problems

    SIM 3-10, set value J to the maximum of 10.

    Failing to plan is planning to fail!!!

  7. #7
    Field Supervisor 500+ Posts
    MX-FN27 inner finisher problems


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    Re: MX-FN27 inner finisher problems

    I looked up the sim 3-10 value J and that looks very promising. If the customer has any more problems this sounds like it will cure for good. I think it is a static problem and my cleaning and firmware update took care of the problem but if it comes back i think this sim will be able to adjust for the belts to have more pressure to overcome static. Thanks

  8. #8
    The Wolf 2,500+ Posts mojorolla's Avatar
    Join Date
    Jan 2010
    Location
    Cleveland OH
    Posts
    2,512
    Rep Power
    125

    Re: MX-FN27 inner finisher problems

    Sharp seems to be blaming static for a lot of things nowadays. I have had a few PCU pwbs on the new machines go due to "static". Grounding strap this retrofit, grounding clips in registration drive, etc....
    I guess it is hard to find a good ground on a machine made of plastic.


    Failing to plan is planning to fail!!!

  9. #9
    Senior member of CRS 2,500+ Posts
    MX-FN27 inner finisher problems

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,367
    Rep Power
    102

    Re: MX-FN27 inner finisher problems

    Quote Originally Posted by mojorolla View Post
    Sharp seems to be blaming static for a lot of things nowadays. I have had a few PCU pwbs on the new machines go due to "static". Grounding strap this retrofit, grounding clips in registration drive, etc....
    I guess it is hard to find a good ground on a machine made of plastic.


    That's why they tape a piece of static brush to paper feed areas and ground that to frame ground ( doesn't always work, if not cleaned and secured though).
    "You can't trust your eyes, if your mind is out of focus" --

  10. #10
    Technician
    Join Date
    Aug 2015
    Location
    NYC
    Posts
    45
    Rep Power
    18

    Re: MX-FN27 inner finisher problems

    Quote Originally Posted by mojorolla View Post
    SIM 3-10, set value J to the maximum of 10.


    Value J can be set only within 90-110. How to set 10?

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here