Results 1 to 9 of 9
  1. #1
    Technician
    Join Date
    Apr 2010
    Posts
    38
    Rep Power
    29

    MX-3070 black screen

    Hello,

    Someone familiar with a complete black display on the MX-3060 of MX-3070?

    Knows someone a possibility for a factory reset? In combination wit sw5?

  2. #2
    Senior Tech 100+ Posts
    MX-3070 black screen

    moose55's Avatar
    Join Date
    Mar 2017
    Location
    Papillion, NE
    Posts
    143
    Rep Power
    16

    Re: MX-3070 black screen

    I am dealing with the same problem! Luckily for me it is a demo floor machine. I "borrowed" the transfer lift clutches for a field machine, and when I put the clutches back on our demo floor MX-4070 the LCD display will not come on? I can hear the machine going through warm up, but no display? I have tried the mSATA card, LVDS PWB, ribbon cable from the LVDS PWB to SCU PWB, all with no luck. I know that the display works as I have tried it on another machine. I thought that maybe I was missing a connector? I went back through (at least 5 times) and found no loose connectors? Sorry I don't have a solution, but I wanted to let you know you are not alone! I would start with the mSATA card. If I get mine solved I will share what I found.
    The Moose is loose!!

  3. #3
    Field Supervisor 500+ Posts
    MX-3070 black screen

    mansart's Avatar
    Join Date
    Apr 2009
    Posts
    843
    Rep Power
    54

    Re: MX-3070 black screen

    Does the screen come up in "emergency firmware" update mode? (DIP switch on MFP board).........

    If so remove the removable EEPROM's from MFP board, SCU board and PCU board and replace with EEPROM's from a known working machine. (Careful not to mix them up) These three chips will only work together, they are a "digitall locked" set.

    If machine comes up with the second set of EEPROM's ..... you must log a call with Sharp tech support and initiate EEPROM reprogramming with Sharp.

    TT-082213_1R4.PDF

  4. #4
    The Wolf 2,500+ Posts mojorolla's Avatar
    Join Date
    Jan 2010
    Location
    Cleveland OH
    Posts
    2,512
    Rep Power
    125

    Re: MX-3070 black screen

    A couple known issues:
    -the cable under the op panel that powers the LCD and backlight can back out of the pwb. They changed the locking clips.
    -FCC cables from MFPSCN board to the op panel are also a known issue. Not fun to replace as the one cable must have the etire scanner unit removed to be replaced. These are the 2 flat white ribbon cable in the upper right of the main board.
    -you can also flip the dip switch on the MFPSCN board and attempt to force calibrate the op panel.
    -since Sharp combined the MFP and SCN boards, I have had dozens of these boards fail as well.


    Failing to plan is planning to fail!!!

  5. #5
    Junior Member
    Join Date
    Mar 2017
    Location
    Cumming, Ga
    Posts
    4
    Rep Power
    0

    Re: MX-3070 black screen

    We had one similar to this and the ROM on the MCU board was the issue.

  6. #6
    Technician
    Join Date
    May 2013
    Posts
    12
    Rep Power
    23

    Re: MX-3070 black screen

    Hi guys,

    Have u found other solutions to this fault?

    Got a black/dim screen after I replaced a toner motor.
    They can still print but ocp has no back light.

    Thanks for your help
    Last edited by brodpete; 03-13-2019 at 09:10 AM.

  7. #7
    Field Supervisor 500+ Posts
    MX-3070 black screen

    mansart's Avatar
    Join Date
    Apr 2009
    Posts
    843
    Rep Power
    54

    Re: MX-3070 black screen

    Double, triple, quadruple check the ribbon cables to the top of MFP board.

  8. #8
    Technician
    Join Date
    Nov 2013
    Location
    Nuernberg
    Posts
    24
    Rep Power
    22

    Re: MX-3070 black screen

    One of my machines had The same issue .
    i checked all The Things .
    at last i found two things .
    on mfp was fired The Fuse for display power. A little Smd-typ . I think 2A of 1,6 . In near of the ribbon-cable to display .
    it was fired by a Not suxxessful connect of the cable.
    The Second was the Board under the Panel.

  9. #9
    Trusted Tech 50+ Posts
    Join Date
    Aug 2011
    Location
    Olympia , Wa
    Posts
    51
    Rep Power
    26

    Re: MX-3070 black screen

    Every time I have seeen this is has been the mSATA causing the problem. You can buy them and program them from a chip out of a new machine using a Apricorn mSATA Wire. Make sure you update the machine to the newest version before copying the chip.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here