Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Technician JPazy's Avatar
    Join Date
    Jul 2019
    Location
    Buffalo, NY
    Posts
    12
    Rep Power
    1

    MX-3570V Duplex misfeeds

    I have a Sharp MX-3570V which misfeeds intermittently when duplexing jam code APPD2_S.When it jams it accordians between MFP duplex guide and Right door duplex guide past the second Duplex drive roller. Occasionally it crease the paper an inch and a half from lead edge, like too much Registration Loop. We have installed updated sensor springs, replaced sensors and guides with no resolution to the problem. Machine runs fine in 8.5 x 11 R direction and seems to run fine when outputting to Right Side Tray. Any ideas?

  2. #2
    Senior Tech 250+ Posts
    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    313
    Rep Power
    25

    Re: MX-3570V Duplex misfeeds

    There is a technical report CCE-2003R2 out for what looks like your problem. It is for modification of ADU enter/exit paper actuator spring. It sounds like the actuator sticks causing jam and they have a new spring out to prevent that problem.PN of new spring is MSPRD4699FCZ1

  3. #3
    Senior Tech 250+ Posts
    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    313
    Rep Power
    25

    Re: MX-3570V Duplex misfeeds

    Sorry, missed where you said you installed new sensor springs, Thats all I have on that problem.

  4. #4
    Technician
    Join Date
    Dec 2008
    Location
    Toledo, Ohio
    Posts
    16
    Rep Power
    22

    Re: MX-3570V Duplex misfeeds

    I know this sounds wierd... but what is your firmware level? I've found in some rare cases that updating the firmware on these models fixes some duplex jamming issues.

  5. #5
    Senior Tech 250+ Posts
    MX-3570V Duplex misfeeds

    mansart's Avatar
    Join Date
    Apr 2009
    Posts
    476
    Rep Power
    32

    Re: MX-3570V Duplex misfeeds

    Check and double check the ribbon cable from right side door to PCU......

    You may want to try adjust for curl, see link below...compliments of mojorolla

    Paper Curl Adj


  6. #6
    Technician JPazy's Avatar
    Join Date
    Jul 2019
    Location
    Buffalo, NY
    Posts
    12
    Rep Power
    1

    Re: MX-3570V Duplex misfeeds

    Thank you, yes double checked firmware is up to date and reflashed it to be certain. Checked ribbon cables, and reseated them. Don't see any damage on the cables.

  7. #7
    Senior member of CRS 2,500+ Posts
    MX-3570V Duplex misfeeds

    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    3,144
    Rep Power
    89

    Re: MX-3570V Duplex misfeeds

    Quote Originally Posted by JPazy View Post
    Thank you, yes double checked firmware is up to date and reflashed it to be certain. Checked ribbon cables, and reseated them. Don't see any damage on the cables.
    Does this machine have a right side exit tray? I saw the cable/connector for the reverse solenoid not properly routed causing the solenoid to not fully open.
    "You can't trust your eyes, if your mind is out of focus" --

  8. #8
    Technician JPazy's Avatar
    Join Date
    Jul 2019
    Location
    Buffalo, NY
    Posts
    12
    Rep Power
    1

    Re: MX-3570V Duplex misfeeds

    Yes, it does have the Right Tray unit, which I haven't experienced any misfeeds when the paper outputs to that tray. I did remove it and installed the original blank guides, but misfeeding during duplex continues. Thank you for the tip, i will check the wiring harness for the solenoid to be sure it's routed correctly.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here