MXM310N Maintaince Required after PM

[redserv]

hello guys i did a PM on MXM310N about 2 weeks ago,changed drum and dev, i cleared all counters etc.... client called yesterday, said they are seeing Maintaince Required on lcd screen, so i went back to the client and yep i saw it for myself, i checked Sim 24 and the drum and developer was only doing 13,724 copies, so i am abit stumped here, was there something i messed up on when i was doing the PM? can someone point me in the right direction please.thanks in advance

[bilyahn]

The only thing I can see is this statement from page 8-31 in service manual. But it applies to sim 24-4 which is the simple maintenance reset. I don't see how this may be helpful but it's all that I can find so far, nothing on the sharp website that I could find for this model. What is the meter on this?

Good luck.

Bil

∗

31 sheet model: When maintenance message is displayed, replaceconsumption part reaching the number of sheets of maintenance,

then clear the replaced part's counter only.

[Lawrence]

When replacing Drum and DV you should reset:
24-4 M-Count
24-5 DV Count
24-7 Drum Count

Double check the M-Count preset in Sim 21. It should be set to 5 for 150k. If it's set to 1 it will pop the counter at 10k.

Also check to see if sim 26-6 is set for your country. Maybe if the machine is set for the middle east they mess around with the m-count preset. I know when you set a new machine from USA to Canada the energy savings are set for 1 minute on auto shut off vs 10 minutes in theUSA.

Just out of curiosity, did this box have network already installed out of the box? In Canada we can't get a "N" model and have to add every option to the machine. I think it's pretty retarded that Sharp was not putting network in these right out of the box. It also needs a color scanner and this would be the perfect machine for a small office...... The engine is a brick Sh!t house and that feeder works really well.

[bilyahn]

Just out of curiosity, did this box have network already installed out of the box? In Canada we can't get a "N" model and have to add every option to the machine. I think it's pretty retarded that Sharp was not putting network in these right out of the box. It also needs a color scanner and this would be the perfect machine for a small office...... The engine is a brick Sh!t house and that feeder works really well.

I agree with you on the color scanner would be a major plus for this machine. In the USA we have to install each part, print, scan memory, fax, etc! Very annoying for us as well.

Bil

[spotlifter]

Maintenance:  MX-M310 
  100k                       Interval:

                                  Process Section:
                                  Replace Developer
                                  Replace OPC Drum
                                  Replace Drum Cleaner Blade
                                  Replace Main Charge Unit
                                  Replace Ozone Filter
                                  Sim 24-05 Clear Developer Counter
                                  Sim 24-07 Clear Drum Counter
                                  Sim 25-02 Toner Concentration Adjustment
                                  Sim 24-04 Clear Maintenance Counter
                                  Paper/Feed & Transport:
                                  Check/Clean/Replace PF Rollers
                                  Sim 24-01 Clear Jam Counter (if required).
                                  Sim 24-02 Clear Individual Tray Counter When P/F Rollers are replaced.
                                  RSPF:
                                  Check/Clean/Replace PF Rollers
                                  Clean all RSPF/RSPF sensors.
                                  General:
                                  Clean all optics, CCD, and white reference plate.
                                  Image Quality:
                                  Sim 40-02 Adjust Copy Exposure Density(B/W).
                                  Other:
                                  Sim 22-05 Data Print

  150k                       Every 150k Interval (perform the additional procedures):
                                  Process Section:
                                  Replace 150k Maintenance Kit:-
                                                  Drum Separator Pawl Unit x 2
                                                  DV Blade
                                                  Transfer Roller Unit
                                                  DV Side Sheet F
                                                  DV Side Sheet R
                                                  Toner Filter Unit
                                  Sim 24-04 Clear Maintenance Counter
                                  Fuser Section: 
                                  Replace Upper Heat Roller Kit:-
                                                  Upper Heat Roller
                                                  Fuser Gear
                                                  Upper Heat Roller Bearing x 2
                                                  Upper Cleaning Pad
                                                  Fuser Separation Pawl Upper x 4
                                                  Thermistor Cleaning Pad
                                  Transfer Section:
                                  Replace Transfer Roller Unit

Thank you to warren.

[redserv]

ah, thanks alot guys i will take closer look into to this, appreciate the feedback