Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16
  1. #11
    Chromographic Supremesist 100+ Posts nightshade's Avatar
    Join Date
    May 2007
    Location
    Upper Midwest
    Posts
    159
    Rep Power
    36
    I agree any of the 2000 series is old and decrepit.

    With that aside. To check to see if the DV magnetic roller is turning. Pull out the drum unit, wipe your finget on the mag roller to brush off a strip of developer, put it back together and make a copy, remove the drum again and see if the roller has turned.

    Also to check to see if you have charge, turn room lighting off and go into crop 8 and run the main charge with the front door cheated. You should see a purplish/blue glow if it is on. Also if you see any "lightning strikes" to the drum, the charge unit is dirty or defective and the arching will cause issues.

    Anotherthing to try to rule out the optics path is to make a copy with the top cover open "skyshot", with this you should get a solid black copy. This works good too when you stop it in mid copy to check for image on the drum.

  2. #12
    aikon_ngage
    Guest

    hey joni

    try to check the xfer corona unit and contact, also dont forget the charge unit w/ grid ,the hvt unit and connectors. also the dv unit if it is rotating or properly set in place. changing developer doesnt help without checking this stuff first.

  3. #13
    Service Manager 100+ Posts deep's Avatar
    Join Date
    Jun 2008
    Posts
    209
    Rep Power
    34
    A post 3 years ago, joni will not back.
    Kenny

  4. #14
    Chromographic Supremesist 100+ Posts nightshade's Avatar
    Join Date
    May 2007
    Location
    Upper Midwest
    Posts
    159
    Rep Power
    36
    Quote Originally Posted by deep View Post
    A post 3 years ago, joni will not back.
    WOW didn't notice. Someone musta been very bored to dig that far back....

  5. #15
    Master Of The Obvious 10,000+ Posts
    Sharp SF-2314 shooting blanks

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,442
    Rep Power
    462
    Oops! If had been paying any attention to the date, I'd have let that one pass......
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  6. #16
    Technician
    Join Date
    Apr 2008
    Location
    Fremont, CA
    Posts
    22
    Rep Power
    33
    Check your corona main charge corona wire if it is not broken. Replace if it is. To check your developer MG roller if it will turn when you run the machine, pull out the developer unit and put a little smudge on the MG developer with your finger and slide the Developer unit back to the machine and start the machine just for a few seconds and shut it off. Slide out the developer unit assembly and check the developer on the MG roller. It it looks smooth and no more smudges then your developer is turning properly.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here