Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1
    Technician siavashsaqi's Avatar
    Join Date
    May 2015
    Location
    tehran
    Posts
    11
    Rep Power
    19

    Unhappy mx-3501 . frequently occures jamming in top of the fiusing

    frequently occures jamming (in top of the fiusing) that the way which ends to exiting transport part.

    in the duplex mode ever ever occures.i mean always occures in the 2sided copies.but in the 1 side copies happening frequently.

    some week ago the transfer belt was torn & i replace it.but now created this problem.


    meanwhile , before replace the belt , machine was work good.




    sorry if i hade Spelling mistakes...

  2. #2
    Trusted Tech 50+ Posts
    Join Date
    Jul 2011
    Location
    castle rock colorado
    Posts
    77
    Rep Power
    26

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    on the transport unit there is a drive gear,i have seen the inside of the gear get worn out ,it does have a pin in the center. good luck

  3. #3
    Technician siavashsaqi's Avatar
    Join Date
    May 2015
    Location
    tehran
    Posts
    11
    Rep Power
    19

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    tnx alot rainmaker, i'll do that

  4. #4
    Technician siavashsaqi's Avatar
    Join Date
    May 2015
    Location
    tehran
    Posts
    11
    Rep Power
    19

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    that drive is well, i clean evry gears & rollers but that problem remained,

    why!? i am deuced!!! there is not any reason for jamming paper!

  5. #5
    Senior Tech 100+ Posts mbcruzin's Avatar
    Join Date
    Aug 2013
    Location
    Murrells Inlet
    Posts
    142
    Rep Power
    24

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    Quote Originally Posted by siavashsaqi View Post
    frequently occures jamming (in top of the fiusing) that the way which ends to exiting transport part.

    in the duplex mode ever ever occures.i mean always occures in the 2sided copies.but in the 1 side copies happening frequently.

    some week ago the transfer belt was torn & i replace it.but now created this problem.


    meanwhile , before replace the belt , machine was work good.




    sorry if i hade Spelling mistakes...
    What are your Jam codes? and How many of each. If its only showing one of each . Go to SIM 26-35 and change the value to 1. This will track frequencies and order of occurrence. I turn this on every machine I can find.

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Oct 2006
    Posts
    230
    Rep Power
    0

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    First of all come back with that jam code,
    Second there is a lot of heat building up so check that the 2 ventilators are working and are not obstructionated

  7. #7
    Technician siavashsaqi's Avatar
    Join Date
    May 2015
    Location
    tehran
    Posts
    11
    Rep Power
    19

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    no....these things wasn't efficcient.
    sim26-35 was on 1 syne.
    but in 1side prints there is no jam anymore.just in 2side mode remain it.
    when jam is occurs, about 2 cm of end of paper remain in the fusing & balled.



    Meanwhile, i had to say sorry vlad robas.i couldn't understand your talk.cause i am iranian & i don't know english very well.but if you rewrite that in the simple english language, i will understant.i hope , you don't get upset from me.
    Last edited by siavashsaqi; 05-03-2015 at 07:33 PM.

  8. #8
    Technician
    Join Date
    Nov 2011
    Location
    Merseyside
    Posts
    40
    Rep Power
    26

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    The 3501 is quite old had has probably seen a lot of service, open up the right side door and check the black paper guide under the gate. its the part that has the notch in it for the sensor arm on the exit of the heater. these guides can warp over time with the heat from the fuser and can stop the fuser exit sensor actuation properly.

  9. #9
    Field Supervisor 500+ Posts ntbann's Avatar
    Join Date
    Jan 2012
    Location
    Port Huron
    Posts
    577
    Rep Power
    34

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    Replace the exit/turnover unit. Over time they warp and sensors go bad. Is there a piece of paper in the exit unit and one coming out of the fuser? Just replaced one last week for duplex jams.

  10. #10
    Technician siavashsaqi's Avatar
    Join Date
    May 2015
    Location
    tehran
    Posts
    11
    Rep Power
    19

    Re: mx-3501 . frequently occures jamming in top of the fiusing

    Quote Originally Posted by ntbann View Post
    Replace the exit/turnover unit. Over time they warp and sensors go bad. Is there a piece of paper in the exit unit and one coming out of the fuser? Just replaced one last week for duplex jams.

    thank you for your aid.yes i told that, whole of paper cross the fuser but just a little section of end of paper (about 1,2 cm) jams & wrinkle in the fusing.you said replace the unit.but in this country (iran),is very hard to find parts of this machine.even maybe not found.& if be found that is very very expensive.i should to fix it without new unit.i'll look that sensors soon & tell result


    sorry for grammar mistakes.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here