Results 1 to 9 of 9
  1. #1
    Service Manager 250+ Posts


    ZeusGT's Avatar
    Join Date
    Feb 2008
    Location
    Tennessee
    Posts
    250
    Post Thanks / Like
    Rep Power
    0

    Used Minolta/Imagistics CF3102/CM2020 Parts

    I have several low mileage CF 3102's and CM2020's that I'm parting out.
    If anybody needs any
    laser units
    glass
    top feeders
    duplexs
    optional drawers (even an LCT)
    motors
    Controller Boards (sorry Firey's are all gone. I have a couple Fiery's that turn on, but don't communicate with the contoller)
    Control Panels
    Or anything else let me know

    support@wes-com.com

    CompTia A+ Certified
    CompTia Net+ Certified
    CompTia Server+ Certified
    CompTia Project+ Certified
    OP Scanshare Certified

  2. #2
    Technician
    Join Date
    Mar 2009
    Location
    West Jordan, Utah
    Posts
    10
    Post Thanks / Like
    Rep Power
    12
    Do you a the PU1 Board?


  3. #3
    Service Manager 250+ Posts


    ZeusGT's Avatar
    Join Date
    Feb 2008
    Location
    Tennessee
    Posts
    250
    Post Thanks / Like
    Rep Power
    0
    Hey TOS-systems,

    yes I do...

    CompTia A+ Certified
    CompTia Net+ Certified
    CompTia Server+ Certified
    CompTia Project+ Certified
    OP Scanshare Certified

  4. #4
    Technician
    Join Date
    Mar 2009
    Location
    West Jordan, Utah
    Posts
    10
    Post Thanks / Like
    Rep Power
    12
    How much? I am installing this in a cf2002 so I'm hoping the cf3102 is compatible. Do you know if it is?


  5. #5
    Service Manager 250+ Posts


    ZeusGT's Avatar
    Join Date
    Feb 2008
    Location
    Tennessee
    Posts
    250
    Post Thanks / Like
    Rep Power
    0
    This is the power supply that you are needing right? The power unit that the three 110 A/C plugs are in for the Fiery controller, scanner and the one for the wall outlet.

    I have an Imagistics CM2020 (which is the CF2002 equivilant) that has a good power supply and has 84,000 copies on it.

    OR if it has to be Minolta, I have a CF2002 good power supply with about 890,000 copies on it.

    Let me know. Thanks

    CompTia A+ Certified
    CompTia Net+ Certified
    CompTia Server+ Certified
    CompTia Project+ Certified
    OP Scanshare Certified

  6. #6
    Technician
    Join Date
    Mar 2009
    Location
    West Jordan, Utah
    Posts
    10
    Post Thanks / Like
    Rep Power
    12
    I hope I can describe this right. I repair computers for a living and bought this printer 2 months ago. 3 weeks after I bought it I walked into the office only to find it had a orange light on the start key and no power any where else. Many hours later I found a bad resister on the PU1 Board. This is the board located directly below the blue paper catch tray. It has the three 110 V plugs that plug into the board. However I just need the board and not the control unit that sits next to it. In the parts manual I believe the part is 4025-6201-02. I have searched for this part for sometime and can not find it. The printer in a minolta dialta cf2002.


  7. #7
    Service Manager 250+ Posts


    ZeusGT's Avatar
    Join Date
    Feb 2008
    Location
    Tennessee
    Posts
    250
    Post Thanks / Like
    Rep Power
    0
    O.k, going back through the parts manual, I can see that the part number that you have is correct for the NA verion (110) and they seem to be the same either way for the CF3102 or the CF2002.

    I would like to be on the safe side and get you one that is specific for the CF2002 just to play it safe. I will get just the board and not the control unit for you if you would like it.

    P.M sent

    CompTia A+ Certified
    CompTia Net+ Certified
    CompTia Server+ Certified
    CompTia Project+ Certified
    OP Scanshare Certified

  8. #8
    Technician
    Join Date
    Mar 2009
    Location
    West Jordan, Utah
    Posts
    10
    Post Thanks / Like
    Rep Power
    12

    Smile

    Just bought a Power Supply board for my CF 2002 from ZeusGT. This was a great transaction and fixed the copier.


  9. #9
    Junior Member
    Join Date
    Mar 2009
    Location
    Elmira, NY
    Posts
    1
    Post Thanks / Like
    Rep Power
    0

    ZeusGT Ripped me off...

    Warning: I purchesed an ADF from ZeusGT, paid for it and he never shipped the unit. Don't let this happen to you. Avoid ZeusGT at all cost.

    To be fair here he did return 12% of my money...

    Last edited by Tech_Guy_Mike; 09-15-2009 at 10:14 AM.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here