Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Field Supervisor 500+ Posts
    E Studio 650 tandem tray wont work


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    E Studio 650 tandem tray wont work

    Hello, this tandem tray wont do anything when closing the drawer. If I turn the machine off then back on the tray will lift and function all normally unless you open the drawer then nothing again unless power off on again. I tested all sensors in the 03 mode and all are working but for some reason the sensor for the paper mis loaded gate that separates the two stacks is working opposite of what the book shows it should,maybe book wrong,I dont know. Other than that it works fine until it is opened again. Maybe someone has seen this before or has some suggestions. Thanks for any help

  2. #2
    Senior Tech 100+ Posts riyadh hossainbd's Avatar
    Join Date
    Dec 2015
    Location
    motijheel,dhaka
    Posts
    238
    Rep Power
    0

    Re: E Studio 650 tandem tray wont work

    Quote Originally Posted by Hansen88 View Post
    Hello, this tandem tray wont do anything when closing the drawer. If I turn the machine off then back on the tray will lift and function all normally unless you open the drawer then nothing again unless power off on again. I tested all sensors in the 03 mode and all are working but for some reason the sensor for the paper mis loaded gate that separates the two stacks is working opposite of what the book shows it should,maybe book wrong,I dont know. Other than that it works fine until it is opened again. Maybe someone has seen this before or has some suggestions. Thanks for any help
    This is not sensor problem , I think drawer switch problem,just clean or change switch it will be ok. this is located rear side,when u push drawer then it will be on

  3. #3
    Field Supervisor 500+ Posts
    E Studio 650 tandem tray wont work


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    Re: E Studio 650 tandem tray wont work

    I went back out there today and changed the wire harness and connector in the back of the machine that the drawer plugs into when you close it. I also changed the logic board and the drawer itself. Still the same problem. Turn the machine off then on and it works as it should until the drawer is opened again. I guess I will try the system board and hdd next. Dont have any other ideas.

  4. #4
    Field Supervisor 500+ Posts
    E Studio 650 tandem tray wont work


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    Re: E Studio 650 tandem tray wont work

    Well I changed the system board and the hdd and still same problem. I am out of ideas, I cant see anything else that would have to do with the drawer that I have not replaced.

  5. #5
    Field Supervisor 500+ Posts
    E Studio 650 tandem tray wont work


    Join Date
    Dec 2009
    Location
    Waukegan IL
    Posts
    956
    Rep Power
    57

    Re: E Studio 650 tandem tray wont work

    Well I went back to customer today with a couple ideas which did not fix it but while checking other things out I lucked into the fix. So all is good now.

  6. #6
    Senior Tech 250+ Posts
    E Studio 650 tandem tray wont work

    arnh79's Avatar
    Join Date
    Apr 2010
    Location
    Canada
    Posts
    445
    Rep Power
    43

    Re: E Studio 650 tandem tray wont work

    Would you mind sharing the fix? Never know when one of us might need the tip.
    Why does every customer think they're the first one to ever say: "you've been here so much we should get you an office, ha, ha, ha"?

  7. #7
    Master Of The Obvious 10,000+ Posts
    E Studio 650 tandem tray wont work

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,442
    Rep Power
    462

    Re: E Studio 650 tandem tray wont work

    Yeah, fess up. Was it particularly stupid, or you're fault? I'm sure you weren't the first to do it. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here