Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6
  1. #1
    Technician copyguy69's Avatar
    Join Date
    Feb 2016
    Posts
    38
    Rep Power
    6

    e Studio 306 White Void

    I have a white void that is produced by the developer unit. Swapped it out with another and problem is gone. The blade gap is correct and there is new developer in the unit. There is no void of developer on the mag roller and am wondering if there is something wrong inside with the mag roller itself. Anyone familiar with this issue? Any suggestions are welcome. Thanks in advance

    copyguy69


  2. #2
    Trusted Tech 50+ Posts
    Join Date
    Sep 2015
    Posts
    91
    Rep Power
    7

    Re: e Studio 306 White Void

    Quote Originally Posted by copyguy69 View Post
    I have a white void that is produced by the developer unit. Swapped it out with another and problem is gone. The blade gap is correct and there is new developer in the unit. There is no void of developer on the mag roller and am wondering if there is something wrong inside with the mag roller itself. Anyone familiar with this issue? Any suggestions are welcome. Thanks in advance

    copyguy69
    Is the void lead to trail or op to non-op ?


  3. #3
    Master Of The Obvious 10,000+ Posts
    e Studio 306 White Void

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,555
    Rep Power
    272

    Re: e Studio 306 White Void

    You may not notice a bare spot on the mag roller when it's sitting on the table, or when you rotate it by hand, but you can't agitate the developing unit at full speed. Most likely, there is a piece of fuzz or foam trapped behind the doctor blade. If you remove the blade assembly I think you'll find the obstruction. Be sure to properly adjust the doctor blade spacing when re-assembling. It's covered in the manual.
    =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Sep 2015
    Posts
    91
    Rep Power
    7

    Re: e Studio 306 White Void

    Quote Originally Posted by blackcat4866 View Post
    You may not notice a bare spot on the mag roller when it's sitting on the table, or when you rotate it by hand, but you can't agitate the developing unit at full speed. Most likely, there is a piece of fuzz or foam trapped behind the doctor blade. If you remove the blade assembly I think you'll find the obstruction. Be sure to properly adjust the doctor blade spacing when re-assembling. It's covered in the manual.
    =^..^=
    I have found, rather than purchase those docblade cleaning mylars, that an inch or so piece of the banding used to hold together paper boxes works pretty good.
    you cut in a V notch..peel up end of V slightly...push in past V then pull back so the notches catch the back side of the blade...run it back and forth to cut off all the stuck toner and fuzz...push the mylar all the way in and retrieve it from the back side...dump/vac to your hearts content.


  5. #5
    Technician copyguy69's Avatar
    Join Date
    Feb 2016
    Posts
    38
    Rep Power
    6

    Re: e Studio 306 White Void

    Thanks for the replies. It was debris in the developer unit. Every time I rotated the roller is had no signs of anything bad but it was.

    copyguy69


  6. #6
    Master Of The Obvious 10,000+ Posts
    e Studio 306 White Void

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    16,555
    Rep Power
    272

    Re: e Studio 306 White Void

    Congratulations on your success. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.


    blackcat: Master Of The Obvious =^..^=

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here