+ Reply to Thread
Page 1 of 2
1 2 LastLast
Results 1 to 10 of 19

Thread: e45 alway paper jam - "misfeed in copier"

  1. #1
    Senior Tech 100+ Posts aalex_bom is an unknown quantity at this point aalex_bom's Avatar
    Join Date
    Jan 2008
    Location
    ASDF
    Posts
    113
    Rep Power
    0

    Exclamation e45 alway paper jam - "misfeed in copier"

    when copier paper jam, we moved paper but cover closed, duplex Closed, copier can not "ready"
    Last edited by aalex_bom; 12-08-2008 at 06:47 AM.

  2. Your text here
  3. #2
    Technical Support 50+ Posts mckinley is on a distinguished road mckinley's Avatar
    Join Date
    Dec 2006
    Location
    Derbyshire, England.
    Posts
    70
    Rep Power
    7
    what error code are you getting?
    i would look at the fuser exit sensor, they commonly fail due to constant heat.
    also i would check all sensors to see if one is being held back by a small piece of paper.
    Happiness Is The Road.

  4. #3
    Senior Tech 100+ Posts aalex_bom is an unknown quantity at this point aalex_bom's Avatar
    Join Date
    Jan 2008
    Location
    ASDF
    Posts
    113
    Rep Power
    0

    Question TURN OFF to ready

    IF I turn off and turn on again then it can run, but when COPIER jam, i take over any paper out then i must turn off copier and restart.

  5. #4
    Senior Tech 100+ Posts Sbarro is on a distinguished road Sbarro's Avatar
    Join Date
    Feb 2008
    Location
    Szczecin
    Posts
    159
    Rep Power
    6
    Yeah. It's front cover sensor ) I had this twice (E45 and E232). Good luck.
    "A process cannot be understood by stopping it. Understanding must move with the flow of the process, must join it and flow with it"

    "
    What do you despise? By this you are truly known"

    Guess who

  6. #5
    Senior Tech 100+ Posts aalex_bom is an unknown quantity at this point aalex_bom's Avatar
    Join Date
    Jan 2008
    Location
    ASDF
    Posts
    113
    Rep Power
    0

    why

    i changed sensor, not ready.

  7. #6
    Technical Support 50+ Posts mckinley is on a distinguished road mckinley's Avatar
    Join Date
    Dec 2006
    Location
    Derbyshire, England.
    Posts
    70
    Rep Power
    7
    you changed which sensor? door? fuser? both?
    does the machine have an LCF? if it does, you have a few pointers...
    broken LCF feed housing ( rocking backwards & forwards at rear side )
    button switch at rearside of LCF not making properly when side door closed.
    microswitch not operating when you close LCF door ( located behind lower side cover nearest floor ) you should hear that click when you open & close the door.
    & finally, the wiring harness for the LCF ( this applies to pedestals also ), if it's not properelly plugged in to the machine, it confuses the logic & makes the machine think it has the other option ( ie: if it has an LCF it thinks it has a PEDESTAL )
    as for the error code? you didn't give that. if you press clear & 8 together you should get the error code.

    good luck.
    Happiness Is The Road.

  8. #7
    Senior Tech 100+ Posts aalex_bom is an unknown quantity at this point aalex_bom's Avatar
    Join Date
    Jan 2008
    Location
    ASDF
    Posts
    113
    Rep Power
    0

    Lightbulb have not

    not LCF, not code when i press clear and 8 hold. because it have not "call sevce.." message.
    i changed sensor, checked door, fuser.
    when i close front cover or duplex unit I hear that "click" and ADRF run for 2 second.

  9. #8
    Senior Tech 100+ Posts Sbarro is on a distinguished road Sbarro's Avatar
    Join Date
    Feb 2008
    Location
    Szczecin
    Posts
    159
    Rep Power
    6
    It must be one of the sensors. Try to switch them for example duplex sensor with lower feed sensor.
    "A process cannot be understood by stopping it. Understanding must move with the flow of the process, must join it and flow with it"

    "
    What do you despise? By this you are truly known"

    Guess who

  10. #9
    Senior Tech 100+ Posts aalex_bom is an unknown quantity at this point aalex_bom's Avatar
    Join Date
    Jan 2008
    Location
    ASDF
    Posts
    113
    Rep Power
    0

    Question WHY

    are you understand? I turn on copier, copier "ready " and I copy more 20 sheet, copier ""tip" sound and "misfeed in copier" message. I left paper out but copier not ready after I close all cover and duplex unit.

  11. #10
    Senior Tech 100+ Posts Sbarro is on a distinguished road Sbarro's Avatar
    Join Date
    Feb 2008
    Location
    Szczecin
    Posts
    159
    Rep Power
    6
    I UNDERSTAND I HAD THIS TWICE !
    How can you explain fact that behavior is identical and front cover sensor WAS damaged ?? After replace it works good. I still thinking that is one of the sensors in your case.
    Have you reload firmware yet ?
    "A process cannot be understood by stopping it. Understanding must move with the flow of the process, must join it and flow with it"

    "
    What do you despise? By this you are truly known"

    Guess who

+ Reply to Thread
Page 1 of 2
1 2 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts