Tech forums for copier repair  

Go Back   Copytechnet.com > Technical Forums > Copier Technical Discussion > Toshiba

GM-2040 for e-studio 720

Toshiba

Reply

 

LinkBack Thread Tools Display Modes
Old 09-24-2009   #1 (permalink)
Technician
 
Join Date: Aug 2009

Viet Nam us texas
Location: saigon
Posts: 12
Rep Power: 0htb2k5 is an unknown quantity at this point
Question GM-2040 for e-studio 720

I had a toshiba Es-720 (firmware T390SY0U329). It is printing/scanning with the trial of 39 days (after change NVRAM of board SYS ...). I have buy a GM-2040 dongle ; but I don't know it is good or bad... I don't dare to end the trial by using 08-799 set =0 by more causes. I format normal USB disk (not GM-2040) with FAT. I do into 03 mode for test (after pluging in turn the normal USB disk and the GM-2040 dongle) : 03-power on > start key > copy key on > 0 key. For the normal USB disk, D and E are highlighted display (-> connectable and acceptable). For the GM-2040 dongle, no any A-H is highlighted display. I think that the good GM-2040 results highlighted display at A.
I pluging the GM-2040 into my PC, i found out driver of Rocky4.
Can you help me for testing GM-2040 ?...
htb2k5 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Old 09-24-2009   #2 (permalink)
Senior Tech
100+ Posts
 
Join Date: Jun 2009

United States us florida
Location: Clearwater
Posts: 184
Rep Power: 2emujo is on a distinguished road
You shouldn't need any type of testing. The GM2040 is the print/scan enabler for this MFP. Once plugged in, the trail period mssg will no longer be displayed, and after inputting proper IP configuration and downloading driver, you should be printing. Also, when enabler is plugged in, your 'SCAN" hard button should now light when depressed. EMujo
emujo is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 09-25-2009   #3 (permalink)
Technician
 
Join Date: Aug 2009

Viet Nam us texas
Location: saigon
Posts: 12
Rep Power: 0htb2k5 is an unknown quantity at this point
thanks emujo for your reply.
When plug in GM2040 to my E720, the trail period mssg still be displayed (with any 08-258 set = 0,1,2).
htb2k5 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 09-25-2009   #4 (permalink)
Senior Tech
100+ Posts
 
Join Date: Jun 2009

United States us florida
Location: Clearwater
Posts: 184
Rep Power: 2emujo is on a distinguished road
08/258 should be at a 1, but this code has no relavance to the print/scan enabler. Did you try to look at the enabler when you plugged it in to your PC? Did you try to make any changes to it? If the enabler has been corrupted, that would explain why the trial period message is still showing. With the enabler plugged in, can you press and light the scan hard button? Look at the enabler itself, what exactly is it labled as? EMujo
emujo is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 09-25-2009   #5 (permalink)
Senior Tech
100+ Posts
 
Join Date: Jun 2009

United States us florida
Location: Clearwater
Posts: 184
Rep Power: 2emujo is on a distinguished road
After a little research, I found a few other items. I can't get this info from toshiba anymore, but maybe someone else can check this for you... Your machine is at ver 329..this version supprorts the new version of enablers (GM 2041) What I don't know is if the new version of firmware supports the older GM2040. Any answers out there? My general feeling is yes, the enablers are backward compatible, and I know the GM 2041 wont work with a lower version. EMujo
emujo is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 09-26-2009   #6 (permalink)
Technician
 
Join Date: Aug 2009

Viet Nam us texas
Location: saigon
Posts: 12
Rep Power: 0htb2k5 is an unknown quantity at this point
Hi emujo,
I have no choice. I do 08-799 set =0 to end the trials. I plug in GM-2040 to MFP , but I don't print/scan by this GM-2040. TopAccess don't show parts of print/scan as before. I will return it and seek other.
htb2k5 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 09-27-2009   #7 (permalink)
Senior Tech
100+ Posts
 
Join Date: Jun 2009

United States us florida
Location: Clearwater
Posts: 184
Rep Power: 2emujo is on a distinguished road
Just a shot in the dark...you aren't plugging the enabler into the slot on the SYS bd are you? This slot is for the data overwrite kit only. The enabler should be plugged into one of the 2 side by side USB ports on the right/rear side of the MFP. Emujo
emujo is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

Tags
720, estudio, gm2040

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Google

All times are GMT +1. The time now is 09:49 AM.


Your Link Here
Toner Chip Resetter
Your Link Here

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.0
Ad Management plugin by RedTyger