+ Reply to Thread
Page 1 of 2
1 2 LastLast
Results 1 to 10 of 12

Thread: eStudio 310C hangs at "Please wait..."

  1. #1
    Junior Member lkaleh is on a distinguished road
    Join Date
    Nov 2009
    Location
    rochester
    Posts
    6
    Rep Power
    0

    eStudio 310C hangs at "Please wait..."

    We had this unit working, mostly, but made a couple changes and have this condition. We are trying to restore a backup configuration but can't get to that menu. Our documentation is incomplete or just too ambiguous. How do we get to the "Restore Backup" menu?

  2. #2
    Field Supervisor 1000+ Posts manuals4you has a spectacular aura about manuals4you has a spectacular aura about manuals4you's Avatar
    Join Date
    Jan 2006
    Location
    Long Island, NY
    Posts
    1,505
    Rep Power
    25
    This Parts & Service manual can now be purchased for $11.77 and downloaded immediately after payment
    from The Internet's largest collection of manuals


    Paul@justmanuals.com
    Want to Fix Something?
    http://www.manuals4you.com

    Now Open;
    http://www.justmanuals.com
    Instant downloads

  3. #3
    Junior Member lkaleh is on a distinguished road
    Join Date
    Nov 2009
    Location
    rochester
    Posts
    6
    Rep Power
    0

    We have the manuals

    The description of the process to get to the Restore Backup menu is ambiguous. It says, "Press the first line selection button on the Control Panel during diagnostics to display the Restore Backup menu and select Restore Backup." What does that mean?

  4. #4
    Field Supervisor 500+ Posts TheOwl has a spectacular aura about TheOwl has a spectacular aura about TheOwl's Avatar
    Join Date
    Nov 2008
    Location
    Tasmania
    Posts
    505
    Rep Power
    9
    What are you trying to restore to the machine?

    Department Codes?
    Address Books?

    Sometimes if you edit these files and restore them to the machine, it will cause a lockup because of an invalid character or something like that.

    If that is the case, then you need to format the HDD and then attempt to reload the backups. Please remember that formatting the HDD will destroy any user and admin data held on the HDD.
    Please don't ask me for firmware or service manuals as refusal often offends.

  5. #5
    Junior Member lkaleh is on a distinguished road
    Join Date
    Nov 2009
    Location
    rochester
    Posts
    6
    Rep Power
    0

    restore

    We have the condition where it hangs at "please wait...". It had been working until we made some minor changes to networking. Thinking it was those changes, we wanted to go back to where it was working. Is there something else we can/should try?

  6. #6
    Field Supervisor 500+ Posts TheOwl has a spectacular aura about TheOwl has a spectacular aura about TheOwl's Avatar
    Join Date
    Nov 2008
    Location
    Tasmania
    Posts
    505
    Rep Power
    9
    Which changes did you make?

    There is a network initialization that you can do from the 08 mode which will reset the NIC back to factory. Have a look in the service manual for this one.
    Please don't ask me for firmware or service manuals as refusal often offends.

  7. #7
    Junior Member lkaleh is on a distinguished road
    Join Date
    Nov 2009
    Location
    rochester
    Posts
    6
    Rep Power
    0

    08 reset

    We have the service manual but there is nothing in the documentation regarding reseting or initializing the network settings in the Setting Mode 08.

  8. #8
    Trusted Tech 50+ Posts audioimaging is building a good name for himself audioimaging's Avatar
    Join Date
    Jul 2009
    Location
    Bowie, MD
    Posts
    66
    Rep Power
    2
    is the please wait message displayed on the copier touch screen or the fiery display? Also, is this the embedded board (X3E+) or the external fiery?

    If it says Please Wait on the copier, I would say you need to format the hard drive (08-690) first. If that fails to resolve, you may have to re-install system software.

    If on the controller, I would definitely lean towards a system software re-install.

    I believe the nic card reset code is not for this machine, but for newer models with built-in controllers (e-bridge machines).

  9. #9
    Junior Member lkaleh is on a distinguished road
    Join Date
    Nov 2009
    Location
    rochester
    Posts
    6
    Rep Power
    0

    Please wait

    If the fiery display is on the left side, that is where the message is displayed. The copier panel (Center) seems to be normal. It copies OK.
    It displays X3E+ during the power up cycle on the lefthand display, so can I assume it is embedded?
    Is the the software loaded from a PC? If so, where can we get the software?

  10. #10
    Service Manager 250+ Posts ivovb is building a good name for himself
    Join Date
    Apr 2008
    Location
    Sofia
    Posts
    278
    Rep Power
    6
    Quote Originally Posted by lkaleh View Post
    If the fiery display is on the left side, that is where the message is displayed. The copier panel (Center) seems to be normal. It copies OK.
    It displays X3E+ during the power up cycle on the lefthand display, so can I assume it is embedded?
    Is the the software loaded from a PC? If so, where can we get the software?
    Check connectors of the fiery. e.g. remove top-left cover to see fiery and reconnect all of the connectors. I have had similar problem with FC22.

    BR

+ Reply to Thread
Page 1 of 2
1 2 LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts