Tech forums for copier repair  

Go Back   Copytechnet.com > Technical Forums > Copier Technical Discussion > Toshiba

E-studio 310c error code CE2

Toshiba

Reply

 

LinkBack Thread Tools Display Modes
Old 02-08-2008   #1 (permalink)
Technician
 
mpact's Avatar
 
Join Date: Jan 2008

Posts: 14
Rep Power: 4mpact is on a distinguished road
E-studio 310c error code CE2

Receive this error code after replacing developer unit and drum. Also replaced image control unit. Anyone with any ideas to resolve this?
mpact is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Old 02-08-2008   #2 (permalink)
service tech
250+ Posts
 
just a tech's Avatar
 
Join Date: Jan 2007

United States
Location: georgia
Posts: 252
Rep Power: 8just a tech is on a distinguished road
per the handbook --

[CE2] Image quality sensor abnormal (no pattern level abnormal)
1. Check that the transfer belt unit is fully raised.
2. Check that the transfer/transport unit is securely inserted.
3. Check for any abnormal stain, large flaw or break on the transfer belt surface.
4. Check that the drum and transfer belt are operating. If abnormal, correct any mechanical
problem

hope this helps.. let me know and i'll try to dig deeper..
just a tech is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 02-10-2008   #3 (permalink)
Technician
 
mpact's Avatar
 
Join Date: Jan 2008

Posts: 14
Rep Power: 4mpact is on a distinguished road
e-studio 310c CE2 error

Check everything in the service manual, still getting this error. Any other ideas?
mpact is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 02-10-2008   #4 (permalink)
Technical Support
50+ Posts
 
mckinley's Avatar
 
Join Date: Dec 2006

United Kingdom uk staffordshire
Location: Derbyshire, England.
Posts: 70
Rep Power: 6mckinley is on a distinguished road
sounds like one of your developers maybe depleted, causing poor patches on the belt.
I would check the devs, if they are all ok, the next thing i'd check is the transfer rollers inside the transfer belt unit ( put conductive grease on the end of the roller where the charging takes place. )
Also make sure all your charger units are located correctly ( the lip that holds the chargers secure gets broken off, allowing the charger to drift out slightly )

don't forget to clean the IQC sensor & Colour Reg. Sensors, then in 05 mode run IQC ( 878 for old parts, 879 if you have fitted new parts )
& Colour Reg. 05 mode code 407.
__________________________
Happiness Is The Road.
mckinley is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 02-11-2008   #5 (permalink)
Technician
 
mpact's Avatar
 
Join Date: Jan 2008

Posts: 14
Rep Power: 4mpact is on a distinguished road
CE2 error gone

Okay got it! Would this also cause poor image quality? Now there is little to no image. Just outlines of image.
mpact is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 02-11-2008   #6 (permalink)
Technical Support
50+ Posts
 
mckinley's Avatar
 
Join Date: Dec 2006

United Kingdom uk staffordshire
Location: Derbyshire, England.
Posts: 70
Rep Power: 6mckinley is on a distinguished road
you have a clear outline, but inside the outline's blank?
if you run a gamma setup, 05 mode ... press 4 then press printer/network, place the chart that comes out on to the glass ( the 2 black blocks facing the original scale at the left ) , type in 643 & press the green start button ( still in 05 mode )
See if that makes the copy come back, if it doesn't you have a problem with your devs by the look of it. If the problem goes after running gamma, then the chances are that your IMG board is stuffed. i had that board play up on a 210c, it gave solid outlines & nothing inside them, when you did a gamma it corrected it's self, then it would go again, ended up going several times a day ( customer had to start doing the gamma themselves )
__________________________
Happiness Is The Road.
mckinley is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

Tags
310c, ce2, code, error, estudio

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Google

All times are GMT +1. The time now is 03:18 AM.


Your Link Here
Toner Chip Resetter
Your Link Here

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.0
Ad Management plugin by RedTyger