Tech forums for copier repair  

Go Back   Copytechnet.com > Technical Forums > Copier Technical Discussion > Toshiba

C 471 in e studio 351c

Toshiba

Reply

 

LinkBack Thread Tools Display Modes
Old 04-07-2008   #1 (permalink)
Technician
 
Join Date: Nov 2007

Palestine
Location: Gaza
Posts: 48
Rep Power: 5Nazakat is on a distinguished road
C 471 in e studio 351c

Dear All

I have problem in e studio 351c.It appears C 471 in no time as we turned on Machine. Heater Board is ok,Heater Section is Ok, But Logic Board seems faulty.When we install This Logic Board to another Machine,it gives same error.Can i rectify it by upgrading the machine? or anyother solutions????
Nazakat is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Old 04-07-2008   #2 (permalink)
Vulcan Inventor of Death
500+ Posts
 
Mr Spock's Avatar
 
Join Date: Aug 2006

United States us florida
Location: tampa,fl
Posts: 587
Rep Power: 12Mr Spock is building a good name for himself
The only thing is to reset the code 08-400-0 and see if it goes away if not then the pwb will need to be replaced.
__________________________
And Star Trek was just a tv show...yeah right!
Mr Spock is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-07-2008   #3 (permalink)
Senior Tech
100+ Posts
 
Sbarro's Avatar
 
Join Date: Feb 2008

Poland
Location: Szczecin
Posts: 155
Rep Power: 5Sbarro is on a distinguished road
[C471/472/475] IH power voltage abnormality or IH initial abnormality
1. Check the AC input voltage
Check if the AC input voltage is within the specified range.
(especially when the heater becomes ON after the power is turned ON (the copier is warming up))
2. Check the thermostat
Check if the thermostat is blown.
3. Check the IH control board
(1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is disconnected?
(2) Check if the fuse on the IH control board has blown.
(3) Replace the IH control board.
4. Check the LGC board
(1) Check if the connector CN334 are disconnected.
(2) Check if the conductor pattern on the board is short- or open-circuited.
(3) Replace the LGC board.
5. Clear the status counter
Change the values "10", "11", "12" of the status counter (08-400) to "0".
Sbarro is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-08-2008   #4 (permalink)
Technician
 
Join Date: Nov 2007

Palestine
Location: Gaza
Posts: 48
Rep Power: 5Nazakat is on a distinguished road
Thanks For Help Dear

Quote:
Originally Posted by Mr Spock
View Post
The only thing is to reset the code 08-400-0 and see if it goes away if not then the pwb will need to be replaced.
I have crossed checked the boards but when i replace Logic Board it appears c 471.When i replace PWB no significant change occured.As i place only Logic Board to Another(Already Working)machine,it give error.
Nazakat is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-08-2008   #5 (permalink)
Vulcan Inventor of Death
500+ Posts
 
Mr Spock's Avatar
 
Join Date: Aug 2006

United States us florida
Location: tampa,fl
Posts: 587
Rep Power: 12Mr Spock is building a good name for himself
Quote:
Originally Posted by Nazakat
View Post
I have crossed checked the boards but when i replace Logic Board it appears c 471.When i replace PWB no significant change occured.As i place only Logic Board to Another(Already Working)machine,it give error.

The code locks the machine until the code has been reset (08-400-0). This is stored in the nvram located on the logic board. If it returns then the logic pwb or the nvram chip is bad. Since this happens on the "working" machine then reset the code and see if the error goes away if not then the board is bad. If it goes away with the board in a working machine then check the parts mentioned in SBARRO's post.
__________________________
And Star Trek was just a tv show...yeah right!
Mr Spock is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-10-2008   #6 (permalink)
Technician
 
Join Date: Nov 2007

Palestine
Location: Gaza
Posts: 48
Rep Power: 5Nazakat is on a distinguished road
Thanks For Help Dear

I have installed Logic Board to another machine last night.it started working as i have applied codes 08-665,666,667,669 after installing board.made some copies and it was fine.(Though it was showing READY(Toner not Recognised)) but machine was producing copies.In the morning same error C-471 occured.
Any other Idea about it?


Quote:
Originally Posted by Mr Spock
View Post
The code locks the machine until the code has been reset (08-400-0). This is stored in the nvram located on the logic board. If it returns then the logic pwb or the nvram chip is bad. Since this happens on the "working" machine then reset the code and see if the error goes away if not then the board is bad. If it goes away with the board in a working machine then check the parts mentioned in SBARRO's post.
Nazakat is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-11-2008   #7 (permalink)
Senior Tech
100+ Posts
 
Sbarro's Avatar
 
Join Date: Feb 2008

Poland
Location: Szczecin
Posts: 155
Rep Power: 5Sbarro is on a distinguished road
Check Power Supply
Sbarro is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 04-11-2008   #8 (permalink)
Technician
 
Join Date: Nov 2007

Palestine
Location: Gaza
Posts: 48
Rep Power: 5Nazakat is on a distinguished road
Thanks

I have checked Logic Board in three different machines.Only Logic board is creating problem.I have upgraded machine through usb but in vain.any other idea?

Quote:
Originally Posted by Sbarro
View Post
Check Power Supply
Nazakat is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Reply

Tags
351c, 471, studio

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Google

All times are GMT +1. The time now is 11:15 PM.


Your Link Here
Toner Chip Resetter
Your Link Here

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.0
Ad Management plugin by RedTyger