Toshiba 256se F 101-4 error

[altu]

Dear

I have machine its give error F101-4 (HDD Problem)

I tired to reset through 0 and 8 but its not going in that mode so i decided to install new hard disk
please any one give me how to install in firmware in new hard disk or any other way without change hard disk
please let me know.

[blackcat4866]

Have you read the service handbook section on HDD replacement? =^..^=

[altu]

Have you read the service handbook section on HDD replacement? =^..^=

No Sir i dnt have service book to change HDD replacement if you give details send in this mail

callemster@gmail.com


Thanks thanks

[blackcat4866]

You might not have noticed, but I don't hand out free manuals. There are plenty of places that sell electronic manuals. Sadly to say, our local purveyor of manuals has passed away.

You'll have no trouble finding another manual seller. =^..^=

[tech07]

Passed away ? Really sad. I bought some test charts from him. I know some did not like him. I considered him a valuable asset for info..

[laitang]

F101-4: Partition mount error (The HDD cannot be connected (mounted) caused by damage to the "/work" partition.)

1. Turn the power of the equipment OFF and check the connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.

2. If the error still occurs after step 1, perform the following.
- Perform [3C] - [5] (Key Backup Restore) and check that each Key Status is "OK".
- If not, recover the key (copy "SRAM Key Status" to "FROM Key Status" or vice versa).

3. If the error persists after step 2, perform
[5]+[C]+[POWER]→2. Recovery F/S→3. /work, and then restart the equipment.

4. If the error persists after step 3, perform
[5]+[C]+[POWER]→3. Initialize HDD→2. /work, and then restart the equipment.

5. If the error still persists after step 4, perform the following.
- Perform [3C] - [3] (Format HDD), and then install "System Software (HD data)" with [49] - [4].

Notes:
The following items will be deleted by performing [3C] - [3] (Format HDD).
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If the error persists after performing step 5, perform step 5 after performing [4]+[C]+[POWER]→1. Revert factory initial status HDD.

6. If the error persists even after step 5, replace the HDD.


Good luck!

[dellt]

Can anyone help me find System Software for Toshiba-STUDIO256SE/306SE/356SE/456SE PLEASE!!!!!!!

[calcnet]

Hello

... i have in service two Toshiba ES 256SE with same problem F101-4
... after dismount from copiators ....hdd... and mount into pc ...with parted magic
i view multiple bad`s from 5% to 70% and smart can`t be read (Toshiba 160GB)...
after install in ES 256se another hdd new (Tosiba 500GB) and format this with (3C)...
view in gparted 3 partition primary type ext3 and 3 part. extended type ext3 ...if try clone this hdd
with clonezzila (after many uncorrectable errors) all folders from sda1 inclusive /work is empty...but new hdd is good smart is good...
...tomorrow try... tutorial posted by laitang (Thank You)...but if don’t work ...anybody are this firmware for usb drive ???

Thanks

[calcnet]

IMG_20160524_100807.jpgIMG_20160524_100834.jpgIMG_20160524_100926.jpg

bads in root partition ...after all procedure error is F101-6....all backup keys is ok...but patient is ...dead

Amin

price is 300 euro + vat.... New HDD from Toshiba with software & install

[didi2005]

IMG_20160524_100807.jpgIMG_20160524_100834.jpgIMG_20160524_100926.jpg

bads in root partition ...after all procedure error is F101-6....all backup keys is ok...but patient is ...dead

Amin

price is 300 euro + vat.... New HDD from Toshiba with software & install

Based on your SMART info screenshot, id c5 is 0 which normally no need to change HDD...What u need to do is perform 3C to format HDD and reinstall firmware...