Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Junior Member
    Join Date
    Jun 2016
    Posts
    6
    Rep Power
    0

    WC 7835 Image Quality problem

    Hello!

    Machine WC 7835 has problem: When printing with magenta on prints in the same place (bottom print) appears light bar. I cleaned LPH unit, changed block fotobarabana- not help. What can be wrong?

  2. #2
    Senior Tech 100+ Posts
    Join Date
    Jun 2013
    Location
    VA
    Posts
    218
    Rep Power
    26

    Re: WC 7835 Image Quality problem

    Swap the magenta drum with another one inside the machine and make prints. If the fade is on the drum color you switched it is the drum. All drums are the same in that machine.

    Hope that helps

  3. #3
    Junior Member
    Join Date
    Jun 2016
    Posts
    6
    Rep Power
    0

    Re: WC 7835 Image Quality problem

    I changed drum cartridge- not helped.

  4. #4
    Senior Tech 100+ Posts
    Join Date
    Jun 2013
    Location
    VA
    Posts
    218
    Rep Power
    26

    Re: WC 7835 Image Quality problem

    Ok so changing the magenta drum still has the fade on the bottom? Is the Magenta Drum or toner cart near end of life, less than 20% remaining? Sign into diagnostics and select Adjustments Tab - select dC612 and print out test pattern 7. If the print comes out and should show all 4 colors, look at magenta, if it is faded at any point and you have swapped the drums with no change then you have a Developer Issue.

    Hope this helps

  5. #5
    Junior Member
    Join Date
    Jun 2016
    Posts
    6
    Rep Power
    0

    Re: WC 7835 Image Quality problem

    Test pattern is printed. Magenta is faded on the bottom of print and I have swapped the drums with no change.
    It mean, magnetic roller may be dirty or or the problem is in the developer?

  6. #6
    Senior Tech 100+ Posts
    Join Date
    Jun 2013
    Location
    VA
    Posts
    218
    Rep Power
    26

    Re: WC 7835 Image Quality problem

    Yes you need to replace or reload the developer housing. Are you familiar with the process of removal? Remember to remove the NVM sticker or write down the number as you will need the 3 digit number after installation. Below are the US Based part numbers.

    848K65676 - Developer housing CMYK
    675K85050 - developer (M)

    Hope this helps.

  7. #7
    Junior Member
    Join Date
    Jun 2016
    Posts
    6
    Rep Power
    0

    Re: WC 7835 Image Quality problem

    Thank you for your help! Final question: If I wont see any dirt on magnetic roller or in housing, I need to replace housing fully or just developer exactly?

  8. #8
    Senior Tech 100+ Posts
    Join Date
    Jun 2013
    Location
    VA
    Posts
    218
    Rep Power
    26

    Re: WC 7835 Image Quality problem

    When you clean out the developer housing, check the mag roller to see if there is any signs of damage like a ding, or stray piece of material that doesnt belong in there. I would just replace the developer charge/powder first and if that doesnt work then the entire housing.

    Hope this calls

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here