Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 2 of 2
  1. #1
    Senior Tech 100+ Posts
    xerox plotter 3001 error j2


    Join Date
    Sep 2011
    Posts
    225
    Rep Power
    31

    xerox plotter 3001 error j2

    anyone help me with this older xerox plotter, 3001, goes through rotation , then kicks error j2. any help appreciated !!

    Thanks,
    Jaime
    Indep. Copier. Svc.

  2. #2
    Senior Tech 100+ Posts
    xerox plotter 3001 error j2


    Join Date
    Mar 2011
    Location
    Baltimore, MD
    Posts
    167
    Rep Power
    28

    Re: xerox plotter 3001 error j2

    The J2 code indicates an over-toned condition.
    I can not copy the formatting from the manual, but here is the text of the troubleshooting RAP. Hopefully it will help.

    J2 High Toner Fault RAP
    The status code J2 is displayed when the toner
    concentration is significantly higher than the
    nominal set point.
    This status code may occur if there is a problem
    with the toner dispensing or the mixing of the
    developer material. The Initial Actions deal with
    the most likely mechanical causes for the J2
    code.
    Initial Actions
    · Ensure that diagnostic code [45] is set
    properly.
    · Ensure that the toner cartridge is not
    defective and that too much toner is not
    being dispensed into the developer housing
    (Refer to OF3 Toner Cartridge RAP).
    · Ensure that the Toner Dispense Solenoid is
    adjusted correctly (ADJ. 9.3) and is not
    binding.
    · Ensure that the Toner Sensor connectors
    P/J 31, 34, and 65 are connected securely.
    · Ensure that the Toner Sensor connector
    P/J34 is connected securely.
    Procedure
    NOTE
    It is not necessary to turn on the Main Drive
    Motor using code [10] before entering code [25].
    Enter the diagnostic mode. Enter the code [4]
    and press Start. Make a record of the control
    point, then press Stop.
    Enter the code [25] to display the Toner
    Concentration value.
    NOTE
    When code [25] is entered the Main Drive Motor
    will not start until the fuser is at the correct
    temperature. The value displayed will flash until
    the reading has stabilized. The cleaning blade
    is engaged when the Main Drive Motor starts.
    The value displayed in code [25] is at least 5
    greater than the value of code [4].
    Y N
    Replace the Controller PWB (REP 3.1). If
    the problem persists, replace the Control
    Panel (PL 1.1).
    Make 3 copies of 82E5980 in the Normal copy
    mode. Check the image density of the last
    copy.
    The density of the 0.70G5 paragraph in the
    center of 82E5980 is greater than or equal to
    paragraph 28.5 on S.I.R 82E7030.
    Y N
    Perform the Electrostatic Series (ADJ 9.3)
    then, return to this RAP.
    Make 3 copies of 82E5980 in the Normal
    copy mode. Check the image density of the
    last copy.
    The density of the 0.70G5 paragraph in
    the center of 82E5980 is greater than or
    equal to paragraph 28.5 on S.I.R
    82E7030.
    Y N
    A B C
    A B C
    Go to Flag 3 and check for an open or
    short circuit.
    There is an open or short circuit.
    Y N
    Replace the toner sensor (REP
    9.11). If the problem persists,
    replace the Controller PWB (REP
    3.1).
    Repair the wires. Enter the code [46]
    and press Start to begin the Auto
    Detone.
    Observe the rotation speed of the toner
    cartridge.
    The rotation speed is fast (about 10 seconds
    per revolution.
    Y N
    Enter the code [46] and press Start to begin
    the Auto Detone.
    Switch off the copier, and disconnect P/J35.
    Switch on the copier, and enter the code [19]
    then [10] and press Start.
    Observe the rotation speed of the toner
    cartridge.
    The rotation speed is slow (about 2 to 4
    minutes per revolution.
    Y N
    D E
    D E
    Visually check the position of the toner
    solenoid shaft.
    The solenoid shaft is retracted.
    Y N
    Perform the Toner Dispense Solenoid
    Adjustment (ADJ 9.3).
    Enter the code [46] and press Start to
    begin the Auto Detone.
    Replace the Toner Solenoid (REP 9.6).
    Enter the code [46] and press Start to
    begin the Auto Detone.
    Go to Flag 1, and check the wires for an open
    or short circuit.
    There is a short circuit.
    Y N
    Replace the Toner Solenoid (REP 9.8).
    Enter the code [46] and press Start to
    begin the Auto Detone. If the problem
    persists, replace the Control PWB.
    Repair the wires. Enter the code [46] and
    press Start to begin the Auto Detone.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here