Results 1 to 7 of 7
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Apr 2014
    Location
    Los Angeles
    Posts
    154
    Post Thanks / Like
    Rep Power
    8

    Xerox Work Center 7556 ITB removal proceedure needed

    Hello, i have a customer that heard a crinkling noise. i found a label stuck to the inside machine above the transfer belt. i removed the fuser, the drums, the drum door release lever, the belt cleaner unit as well as the waste container. i suspect that the drive coupler needs to be retracted, maybe in service mode. but i cheched there and didnt see anything pertaining to that.
    does anyone know what i need to do, or just run??

    thank you very much for any help. have a great weekend, Jim


  2. #2
    Man About Town 250+ Posts CanonSco's Avatar
    Join Date
    Jul 2010
    Posts
    365
    Post Thanks / Like
    Rep Power
    18

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    Almost.
    Lower lhs door flat.
    2 spring loaded brackets one either side / just under the fuser removed.
    Grey release plunger pulled out at rear underside of fuser.


    That's it. Pull itb out.

    Yes, I am a nerd.
    Gaming PC - check. Raspberry Pi - Check. Custom ROM on phone - check. Thick glasses - check.

  3. #3
    Senior Tech 100+ Posts
    Join Date
    Apr 2014
    Location
    Los Angeles
    Posts
    154
    Post Thanks / Like
    Rep Power
    8

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    oh, cool. so, to recap. to lower the left side door flat, should i disconnect the rear door support limiter bracket? and the rear plunger, is that accessed from the back of the machine, but is about where the under side of the fuser is??


  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Feb 2011
    Location
    West Palm Beach, Fl.
    Posts
    58
    Post Thanks / Like
    Rep Power
    14

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    Here it is direct from the manual.

    1. Remove the Imaging Unit (Y/M/C/K) (REP 1.2, page 8-10).
    2. Remove the IBT Belt Cleaner Assembly (REP 6.1, page 8-57).
    3. Remove the KL Clip that secures the Rear Strap at the rear, and remove the
    Rear Strap from the L/H Cover Assembly.
    4. Use a needle-nose plier to turn the Left Hand Door Support strap at the front
    counterclockwise by 90 and pull it towards you. Turn it back at the inner
    stopper position, then incline the L/H Cover Assembly horizontally until it stops
    5. Turn the Tension Lever counterclockwise.
    6. Remove 1 screw (silver, 8mm) that secures the Tension Lever and remove the tension lever
    7. Remove 1 screw (silver, 8mm) that secures the Front Lock Bracket and remove
    the Front Lock Bracket.
    8. Remove 1 screw (silver, 8mm) that secures the Rear Lock Bracket and remove the Rear Lock Bracket
    9. Pull the Stopper Lever Latch.
    Caution
    Do not move the IBT Belt Unit out too far to prevent from dropping the IBT
    Belt Unit.
    10. Release the latch.
    11. Pull out the IBT Belt Unit by holding onto the indicated section (A) until the
    Handle at the front/rear become accessible.
    12. Lift the IBT Belt Unit upward using the Handles at the front/rear and slide the IBT Belt Unit toward you to remove it.

    Sorry I couldn't cut and paste the diagrams


  5. #5
    Senior Tech 100+ Posts
    Join Date
    Apr 2014
    Location
    Los Angeles
    Posts
    154
    Post Thanks / Like
    Rep Power
    8

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    thank you Rockdude and CanonSco.
    so, line item # ( "9. Pull the Stopper Lever Latch. ), is that the "gray release plunger, at rear underside fuser" ?

    i have to drive 15 miles into downtown to get there, so i want to be prepared.
    sorry for the trouble. thank you very much guys. have a very nice day, JIm


  6. #6
    Trusted Tech 50+ Posts
    Join Date
    Feb 2011
    Location
    West Palm Beach, Fl.
    Posts
    58
    Post Thanks / Like
    Rep Power
    14

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    Yes, That is the correct lever.

    Be careful with two spring loaded lock brackets.

    They ONLY go in a certain (correct) way.

    Also when reinstalling the IBT assembly make sure you line it up correctly, DON'T FORCE IT!

    Good luck.


  7. #7
    Senior Tech 100+ Posts
    Join Date
    Apr 2014
    Location
    Los Angeles
    Posts
    154
    Post Thanks / Like
    Rep Power
    8

    Re: Xerox Work Center 7556 ITB removal proceedure needed

    ok cool. thank you very much.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here