Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Technician
    Join Date
    May 2014
    Posts
    33
    Rep Power
    11

    Xerox Colorqube 9301 Error 089-520

    have someone a hint where the fault was or knowing Issue, for the Error 89-520-00 Home Sensor Timeout RAP ?

    DC625 Calibration also will not work
    thanks
    Paul

  2. #2
    Service Manager 2,500+ Posts
    Xerox Colorqube 9301 Error 089-520

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    4,525
    Rep Power
    74

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by LamsterPaul View Post
    have someone a hint where the fault was or knowing Issue, for the Error 89-520-00 Home Sensor Timeout RAP ?

    DC625 Calibration also will not work
    thanks
    Paul
    of course the calibration won't pass .. you have an error ... that must be cleared first... hopefully you have the SM ( never go out on a xerox without one )

  3. #3
    Technician
    Join Date
    May 2014
    Posts
    33
    Rep Power
    11

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by Phil B. View Post
    of course the calibration won't pass .. you have an error ... that must be cleared first... hopefully you have the SM ( never go out on a xerox without one )
    Yep, has a service manual,
    have working the process trough, but the error will still come back,I think the sensor or the unit was faulty, so i order a new one, and hope it will work

  4. #4
    Senior Tech 100+ Posts
    Xerox Colorqube 9301 Error 089-520


    Join Date
    May 2014
    Posts
    168
    Rep Power
    12

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by LamsterPaul View Post
    have someone a hint where the fault was or knowing Issue, for the Error 89-520-00 Home Sensor Timeout RAP ?

    DC625 Calibration also will not work
    thanks
    Paul
    This is usually caused by paper dust clogging up the home sensor on the registration pre-heat assembly.

    Clean the sensor.

    If that doesn't work replace the entire regi assembly. Takes five minutes.

    I have a whack of these used to swap in when they get dirty.

    Cheap paper will cause this error within 20,000 copies.

  5. #5
    Junior Member
    Join Date
    Jan 2019
    Location
    Ulaanbaatar
    Posts
    5
    Rep Power
    0

    Re: Xerox Colorqube 9301 Error 089-520

    Hi, I have a Xerox CQ 9303, the same problem appeared 89-520-00 Home Sensor Timeout RAP. I performed the DC330, both motors work well, when the shaft is turned manually, the sensor responds (HI (x), LOW (x)). But the problem does not disappear. I have SM Need help pls.

  6. #6
    Technician
    Join Date
    May 2014
    Posts
    33
    Rep Power
    11

    Re: Xerox Colorqube 9301 Error 089-520

    Hi, I replace the complete PreHeat Assembly (801K37710) and the fault was gone

  7. #7
    Junior Member
    Join Date
    Jan 2019
    Location
    Ulaanbaatar
    Posts
    5
    Rep Power
    0

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by LamsterPaul View Post
    Hi, I replace the complete PreHeat Assembly (801K37710) and the fault was gone
    yes, of course, the problem should disappear after that
    Maybe there is an option to repair this unit

  8. #8
    Senior Tech 100+ Posts
    Xerox Colorqube 9301 Error 089-520


    Join Date
    May 2014
    Posts
    168
    Rep Power
    12

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by Odin View Post
    yes, of course, the problem should disappear after that
    Maybe there is an option to repair this unit
    You don't repair the registration assembly. You throw it out and get a new one.

    Garbage is garbage, and these units get old and brittle. Sensor flag breaks off home drive gear, etc.

    Toss it.

    Sent from my SM-T530NU using Tapatalk

  9. #9
    Service Manager 2,500+ Posts
    Xerox Colorqube 9301 Error 089-520

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    4,525
    Rep Power
    74

    Re: Xerox Colorqube 9301 Error 089-520

    Quote Originally Posted by Odin View Post
    Hi, I have a Xerox CQ 9303, the same problem appeared 89-520-00 Home Sensor Timeout RAP. I performed the DC330, both motors work well, when the shaft is turned manually, the sensor responds (HI (x), LOW (x)). But the problem does not disappear. I have SM Need help pls.
    you really should start a new thread.

  10. #10
    Junior Member
    Join Date
    Jan 2019
    Location
    Ulaanbaatar
    Posts
    5
    Rep Power
    0

    Re: Xerox Colorqube 9301 Error 089-520

    Thanks to everyone, I will look for a replacement.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here