Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Junior Member
    Join Date
    Mar 2018
    Location
    Curacao
    Posts
    3
    Rep Power
    0

    Xerox Workcentre 4250 jams entrance Fuser

    After replacing Fuser (new) paper jams right at entrance Fuser unit. Noise like motor stopping.


  2. #2
    Service Manager 1,000+ Posts
    Xerox Workcentre 4250 jams entrance Fuser

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    2,453
    Rep Power
    39

    Re: Xerox Workcentre 4250 jams entrance Fuser

    Quote Originally Posted by RAFO View Post
    After replacing Fuser (new) paper jams right at entrance Fuser unit. Noise like motor stopping.
    besides fuser what have you done?
    jam code?
    page count on consumables?

    really need more diagnosis before we can help


  3. #3
    Senior Tech 100+ Posts
    Join Date
    Feb 2011
    Location
    West Palm Beach, Fl.
    Posts
    125
    Rep Power
    17

    Re: Xerox Workcentre 4250 jams entrance Fuser

    Phil B correct in order to properly diagnose problem it would be very helpful to have addtional information.

    That being said, check the fuser exit sensor. It breaks easily when installing fuser, as well as sticking.

    Good luck

    Last edited by rockdude; 1 Week Ago at 04:06 PM. Reason: spelling

  4. #4
    Junior Member
    Join Date
    Mar 2018
    Location
    Curacao
    Posts
    3
    Rep Power
    0

    Re: Xerox Workcentre 4250 jams entrance Fuser

    I have checked the Fuser unit and turned drive by hand and found the pressure roller has a flat spot. The Fuser comes in the box with heat and pressure roller latched. This causes the pressure roller to become deformed! Can this be the cause of the motor stalling when Fuser rotates?


  5. #5
    Service Manager 1,000+ Posts
    Xerox Workcentre 4250 jams entrance Fuser

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    2,453
    Rep Power
    39

    Re: Xerox Workcentre 4250 jams entrance Fuser

    Quote Originally Posted by RAFO View Post
    I have checked the Fuser unit and turned drive by hand and found the pressure roller has a flat spot. The Fuser comes in the box with heat and pressure roller latched. This causes the pressure roller to become deformed! Can this be the cause of the motor stalling when Fuser rotates?
    not likely.. you will hear thumping...
    like Rockdude said ... check exit sensor


  6. #6
    Junior Member
    Join Date
    Mar 2018
    Location
    Curacao
    Posts
    3
    Rep Power
    0

    Re: Xerox Workcentre 4250 jams entrance Fuser

    Iím gonna check it out guys. Will keep you posted. Thx for the tips.


  7. #7
    Senior Tech 100+ Posts
    Join Date
    Jun 2013
    Location
    VA
    Posts
    194
    Rep Power
    14

    Re: Xerox Workcentre 4250 jams entrance Fuser

    If the fuser has a flat spot. It will take 10 mins to break open and replace the roller. 2 screws, 2 springs and viola its open. Exit sensor issues with allow paper to enter fuser just not exit or exit and give jam code. Flat spots as mentioned will give a "thumping" noise. Check to make sure transfer roller assy is secured in right hand door. What jam code do you get?


    Hope this helps


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here