Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Apr 2010
    Location
    Lagos
    Posts
    319
    Rep Power
    0

    94-322 on DC 252

    I'm please requesting anyone that has access to eureka snaps to search out some solutions to 094-322 code on DC252 for me. The RAP in the manual does not solve my own case....many of the motors including the main and dev drive motors don't respond, not even in diagnostics. Pls SOS, thanks.


  2. #2
    Service Manager 1,000+ Posts
    94-322 on DC 252

    bojans's Avatar
    Join Date
    Feb 2008
    Location
    Sarajevo East
    Posts
    1,222
    Rep Power
    35
    Quote Originally Posted by adeyemi View Post
    .many of the motors including the main and dev drive motors don't respond, not even in diagnostics.
    Clean or replace front cover interlock switch


  3. #3
    independant techn. 50+ Posts
    Join Date
    Dec 2009
    Posts
    88
    Rep Power
    0
    855758.094-322 at power ON Machine indicates status code 094-322 during power ON



    Cause:


    Followed RAP with tried DC330 Stacking main motor ON with 2 nd BTR retract & 2 nd BTR contact alternatively.But DC330 failed due to Main motor is had initial momentum with humming noise & not able to rotate.








    Replacing Main motor rectified the problem


  4. #4
    Senior Tech 250+ Posts
    Join Date
    Apr 2010
    Location
    Lagos
    Posts
    319
    Rep Power
    0
    Well Bojans thanks, but the display shows the appropriate prompts as you open and close the front cover, i.e it tells u to close the front cover if u boot the machine up with opened front cover and resumes with the 094-322 fault code as soon as you close it up....does this not indicate that the front cover interlock is functioning well?


  5. #5
    Senior Tech 250+ Posts
    Join Date
    Apr 2010
    Location
    Lagos
    Posts
    319
    Rep Power
    0
    Gregoryk, thanks. I tried this, i.e replacing main motor, same problem!!! Anything else? Thanks in advance


  6. #6
    Service Manager 1,000+ Posts
    94-322 on DC 252

    bojans's Avatar
    Join Date
    Feb 2008
    Location
    Sarajevo East
    Posts
    1,222
    Rep Power
    35
    Quote Originally Posted by adeyemi View Post
    Well Bojans thanks, but the display shows the appropriate prompts as you open and close the front cover, i.e it tells u to close the front cover if u boot the machine up with opened front cover and resumes with the 094-322 fault code as soon as you close it up....does this not indicate that the front cover interlock is functioning well?
    I know that. Didn't say it wasn't working.

    I'm telling you clean contacts inside the interlock, and post back.
    I had this problem on many machines. Interlock works in way you described, but it gets dirty and doesn't give good voltage and motor can't start.


  7. #7
    Senior Tech 250+ Posts
    Join Date
    Apr 2010
    Location
    Lagos
    Posts
    319
    Rep Power
    0
    Ok pal, I'll do this and report back to u, thanks


  8. #8
    Service Manager 1,000+ Posts
    94-322 on DC 252

    bojans's Avatar
    Join Date
    Feb 2008
    Location
    Sarajevo East
    Posts
    1,222
    Rep Power
    35
    I just checked my eureka . I don't have snaps for 252, but have 250, it should be the same...

    1. Harness for the Duplex in sensor is pinched between the fuser and the metal frame causing Fuse F5001 on the Main LVPS to blow.
    ===Replace the Fuse, and repair the harness to the Duplex in Sensor===

    2. Paper getting behind transfer drawer. When customer closes transfer drawer module the double plug connector can get broken and or contact pins in the connector get crossed causing a 094-322 failure

    Hope this help

    Good luck


  9. #9
    Senior Tech 250+ Posts
    Join Date
    Apr 2010
    Location
    Lagos
    Posts
    319
    Rep Power
    0
    I'll check all these out, thanks again


  10. #10
    independant techn. 50+ Posts
    Join Date
    Dec 2009
    Posts
    88
    Rep Power
    0
    Quote Originally Posted by adeyemi View Post
    Gregoryk, thanks. I tried this, i.e replacing main motor, same problem!!! Anything else? Thanks in advance
    500896.A fault or error has occurred See user guide for info fc 94-322 500896.A fault or error has occurred See user guide for info fc 94-322 At power on, the UI displays the message ''A fault or error has occurred. See user guide for information on fault code 94-322''. The 94-322 RAP fails to fix the problem. A Software upgrade and replacing the IOT driver, MCU and ESS pwbs+Power Unit+ Initializing the IOT with DC301 did not fix the problem.



    Cause:


    Scrap paper sitting inside J/607. There could have been a paper jam of a coated stock. The customer removed the bulk of the paper but a tiny piece, the size of a finger nail was folded inside the plug/jack on the IOT frame side. It had embedded inside the space inside the p/j607 and was not visible from the outside

    adeyemi.eureka has to many solutions for this problem i'll try to sent you the most common GOOD LUCK!!!


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here