Hi, could you tell me know to enter service mode on Xerox DocuCentre III C2200 Copier Thanks
Thanks: 0
Likes: 0
Dislikes: 0
Hi, could you tell me know to enter service mode on Xerox DocuCentre III C2200 Copier Thanks
Re: Service Mode
Buy a manual and read it.
Originally Posted by JustManuals.com
This is called BTM then RTFM.
Why do they call it common sense?
If it were common, wouldn't everyone have it?
I had asked you for this year ago, do you have now, model xerox docucentre III C2200
you are just awesome
help a guy out
I don't think helping the guy out is really helping the guy out, he is obviously not trained on Xerox so giving him the access to service if he has no clue on what to do will possibly cause injuries or his repair bill much higher than if he had called for service straight away. Costing him more money does not make you his hero duanew. So hknwbec if you had asked Paul for this manual years ago then you don't really have a problem or looking for free fixes and if you really have a problem there are other here on this site who have offered to sell anyone who is willing to pay the pws with the manual of your choice, yes I know its expensive but knowledge is not free. If you can't find it here there is the whole world on the internet someone should sell you a manual for cheap. Good luck to you.
Get your facts first, and then you can distort them as much as you please.
Re: Service Mode
Look's Like The 2200 is a Overgrown 7345
Here try this Hope it's help
Im not worried about your repair bill are your abilities to fix machines these forums are meant to help people not
to just make a sale
I remember back in the day where i help 1 of the guys above and now there acting like this
so here ya go
Access UI Diagnostics by following the procedures below.
Entering UI Diagnostics
At the Control Panel, press and hold the 0 key for 5 seconds, then press the Start button while still pressing the 0 key.
The CE Mode - Password Entry screen will appear.
Enter the Access Number 6789 and press Confirm.
The colors on the display are reversed to indicate that UI Diagnostics mode is active.
Accessing Diagnostic routines
WorkCentre 7132 Maintenance/Diagnostics entry.
Press the Log In/Out button on the Control Panel.
Select System Settings.
Select Common Settings.
Select Maintenance/Diagnostics.
WorkCentre 7232/7242 Maintenance / Diagnostics entry.
Press the Machine Status button on the Control Panel.
Select the Tools tab on the UI.
Select Common Settings.
Under the Group column select Common Settings.
Under Features column use the down arrow and scroll to Maintenance / Diagnostics.
Common to WorkCentre 7132 and WorkCentre 7232/7242.
The following Diagnostics Routines can be accessed from the UI screen. ( Figure 1)
NVM Read/Write
Follow the instructions on the screen. If one or more NVM locations is changed, the machine will reboot upon exit.
Component Control
Sub System
Initialize Hard Disk
Delete All Data
Software Options
Fax Diagnostics
Print Test Pattern
Initialize NVM
Adjustment/Others
Machine ID/Billing Data
Initialize HFSI Counter
Adjust Toner Density
Tray 5 (Bypass) Guide Adjustment (Tray 5=MPT)
Max Setup
Faults
Figure 1. Maintenance/Diagnostics
Exiting UI Diagnostics
CAUTION
Ensure that the machine is not inadvertently left in UI Diagnostics.
There are three ways to exit from UI Diagnostics.
Switch the power off and on.
Perform the following:
Press Close to exit any of the service screens that were opened.
When the System Settings screen is displayed, press Exit.
When the reversed-color Copy Mode screen is displayed, press the Start button while the 0 key is pressed.
If the Restart button is displayed on the screen, pressing the button will exit UI Diagnostics and restart the operation.
Hi Duanew , Thanks for your informations , I will try to know more about it and thanks all of you here to pay attention on this matter
Reply With Quote
Bookmarks