Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Independent technician 100+ Posts jayc67's Avatar
    Join Date
    Sep 2009
    Location
    Strasbourg
    Posts
    101
    Rep Power
    0

    [DC260] White line in tint area

    Hello everybody!

    I have this problem on my 2 Xerox DC260 and I change a lot of parts and nothing change.
    I put in my message a picture.

    scan_yellow_def.pdfscan_yellow_def.pdf

  2. #2
    Service Manager 1,000+ Posts
    [DC260] White line in tint area

    adriansto's Avatar
    Join Date
    Nov 2007
    Location
    Somewhere in Europe near Black Sea
    Posts
    2,231
    Rep Power
    71

    Re: [DC260] White line in tint area

    Always you must indicate where the lead edge is.
    The most common reasons for this white line is the dirty ROS ( laser ) window or dirty into developer house and line into developer material from developer roll.
    These are true if you see same defect on the IBT belt
    For me looks like dirty ROS window.

  3. #3
    Senior Tech 100+ Posts
    [DC260] White line in tint area


    Join Date
    Dec 2010
    Location
    Albany, NY
    Posts
    197
    Rep Power
    28

    Re: [DC260] White line in tint area

    I agree, clean the ROS.

  4. #4
    Independent technician 100+ Posts jayc67's Avatar
    Join Date
    Sep 2009
    Location
    Strasbourg
    Posts
    101
    Rep Power
    0

    Re: [DC260] White line in tint area

    Thanks.

    I already clean and change ROS and I change every developer and clean dev blocks.

  5. #5
    Service Manager 1,000+ Posts
    [DC260] White line in tint area

    adriansto's Avatar
    Join Date
    Nov 2007
    Location
    Somewhere in Europe near Black Sea
    Posts
    2,231
    Rep Power
    71

    Re: [DC260] White line in tint area

    Is this the situation you must check where the line appear first. Print separate colors C,M,Y,K, 40% densities and check how the image looks on every drum and how it looks on IBT for every color. You must panic stop the copier to do these checkings. If these IBT images are clean then look at the 2nd BTR for wear

  6. #6
    Senior Tech 250+ Posts
    Join Date
    Feb 2009
    Location
    Rogers, Arkansas
    Posts
    466
    Rep Power
    35

    Re: [DC260] White line in tint area

    The dirt is on the inside mirrors of the ROS.

  7. #7
    Field Supervisor 500+ Posts Exok's Avatar
    Join Date
    Jun 2011
    Location
    Edison, NJ
    Posts
    750
    Rep Power
    39

    Re: [DC260] White line in tint area

    It does look like a dirty ROS window to me as well.

    You'll need to give us a bit more information to go on though.

    1. Do the void areas show up on all colors? C,M,Y,K (run test patterns for each)

    2. If you are only getting it one 1 color did you:
    a. Clean the ROS window for that color (remove the drum drawer and IBT and really get in there to look at the ROS window from under the ROS)
    b. You said you replaced the developer, did you also replace the developer housing for that color?
    c. Have you inspected the 1st IBT roller for that color?

    3. If the voids show up on all colors, what is the condition of the IBT and the 2nd BTR?

  8. #8
    Independent technician 100+ Posts jayc67's Avatar
    Join Date
    Sep 2009
    Location
    Strasbourg
    Posts
    101
    Rep Power
    0

    Re: [DC260] White line in tint area

    I will try to open and clean the ROS.

  9. #9
    Independent technician 100+ Posts jayc67's Avatar
    Join Date
    Sep 2009
    Location
    Strasbourg
    Posts
    101
    Rep Power
    0

    Re: [DC260] White line in tint area

    Quote Originally Posted by Exok View Post
    It does look like a dirty ROS window to me as well.

    You'll need to give us a bit more information to go on though.

    1. Do the void areas show up on all colors? C,M,Y,K (run test patterns for each)

    2. If you are only getting it one 1 color did you:
    a. Clean the ROS window for that color (remove the drum drawer and IBT and really get in there to look at the ROS window from under the ROS)
    b. You said you replaced the developer, did you also replace the developer housing for that color?
    c. Have you inspected the 1st IBT roller for that color?

    3. If the voids show up on all colors, what is the condition of the IBT and the 2nd BTR?
    Answer :

    1. No it's just 1 or 2 colors
    2.a. I will try
    b. No i just replace developer not the housing but i check if it was a defect on it.
    c. no i don't inspected the 1st BTR. I will change it with another color.

  10. #10
    Junior Member
    Join Date
    Aug 2013
    Posts
    9
    Rep Power
    0

    Re: [DC260] White line in tint area

    clean inside ROS mirrors

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here