ImagePress C6000VP AB2 LTRR jam 1042

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • markdmt
    Technician

    50+ Posts
    • Dec 2009
    • 76
    #1

    ImagePress C6000VP AB2 LTRR jam 1042

    I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
    10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

    I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
    finisher version 4101.0.0.0.0.0.0
    AB2
    Controller 9201.8203.7903
    Tags: 1042, c6000vp, finisher, imagepress, jam
    • teckat
      Field Supervisor

      Site Contributor
      10,000+ Posts
      • Jan 2010
      • 16083
      #2
      Re: ImagePress C6000VP AB2 LTRR jam 1042

      Originally posted by markdmt
      I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
      10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

      I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
      finisher version 4101.0.0.0.0.0.0
      AB2
      Controller 9201.8203.7903
      1. Try Adjusting the Saddle Alignment Reference


      2. C7000VP / C6000VP / C6000, Saddle Finisher-      AB2

      Check PS106 in the Edge Stopper Assembly for proper operation.
      Replace the sensor if necessary.
      Also, the sensor cable to PS106 in the Edge Stopper Assembly flexes up and down with the Edge Stopper and may have a break in the wiring as was found in some cases.
      See picture below for cable location and part number, (Figure L57 in parts catalog).


      Last edited by teckat; 06-01-2017, 03:12 PM.
      **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • markdmt
          Technician

          50+ Posts
          • Dec 2009
          • 76
          #3
          Re: ImagePress C6000VP AB2 LTRR jam 1042

          Originally posted by teckat
          1. Try Adjusting the Saddle Alignment Reference


          2. C7000VP / C6000VP / C6000, Saddle Finisher-          AB2

          Check PS106 in the Edge Stopper Assembly for proper operation.
          Replace the sensor if necessary.
          Also, the sensor cable to PS106 in the Edge Stopper Assembly flexes up and down with the Edge Stopper and may have a break in the wiring as was found in some cases.
          See picture below for cable location and part number, (Figure L57 in parts catalog).


          Forgive me for not knowing how to set the Saddle Alignment Reference? is that part of the adjustments when replacing the finisher control eeprom? section 5 of the AB2 service manual?
          I don't think this is a sensor issue because i have swapped with two other finishers. however all three of these have had finisher boards replaced and new eeproms. These all seem to work like normal except this issue with the paper coming down and stopping before it goes into the saddle folder area. Thanks

            Comment

            • teckat
              Field Supervisor

              Site Contributor
              10,000+ Posts
              • Jan 2010
              • 16083
              #4
              Re: ImagePress C6000VP AB2 LTRR jam 1042

              Originally posted by markdmt
              I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
              10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

              I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
              finisher version 4101.0.0.0.0.0.0
              AB2
              Controller 9201.8203.7903
              in manual 5-37/7
              5.3.2.15 Adjusting the Saddle Alignment Reference



              does LTR-R run ok into all Finisher trays (non-Booklet mode)
              **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                Comment

                • markdmt
                  Technician

                  50+ Posts
                  • Dec 2009
                  • 76
                  #5
                  Re: ImagePress C6000VP AB2 LTRR jam 1042

                  Originally posted by teckat
                  in manual 5-37/7
                  5.3.2.15 Adjusting the Saddle Alignment Reference



                  does LTR-R run ok into all Finisher trays (non-Booklet mode)


                  Not sure on that. i had them offline fold and staple the little job but need to get it fixed. i will get back to it. THX

                    Comment

                    • markdmt
                      Technician

                      50+ Posts
                      • Dec 2009
                      • 76
                      #6
                      Re: ImagePress C6000VP AB2 LTRR jam 1042

                      Originally posted by markdmt
                      Not sure on that. i had them offline fold and staple the little job but need to get it fixed. i will get back to it. THX
                      the LTR-R does run into both upper trays without issue. just looks like it stops at the buffer waiting area and jams before it even goes into the folder area.

                        Comment

                        • teckat
                          Field Supervisor

                          Site Contributor
                          10,000+ Posts
                          • Jan 2010
                          • 16083
                          #7
                          Re: ImagePress C6000VP AB2 LTRR jam 1042

                          Originally posted by markdmt
                          the LTR-R does run into both upper trays without issue. just looks like it stops at the buffer waiting area and jams before it even goes into the folder area.


                          Does booklet LTRR jam using print driver and a walk up test on control panel ?
                          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

                            Comment

                            • markdmt
                              Technician

                              50+ Posts
                              • Dec 2009
                              • 76
                              #8
                              Re: ImagePress C6000VP AB2 LTRR jam 1042

                              Originally posted by teckat
                              Does booklet LTRR jam using print driver and a walk up test on control panel ?
                              Yes

                                Comment

                                Previous template Next
                                Working...