Canon iR2545

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • kuby
    replied
    Re: Canon iR2545

    Originally posted by nicknt82
    As you said " the engine does not respond to anything, only the power light is on." So how can you reload F/W ?

    If you can go on Service Mode, you can try reload F/W.
    ***************************

    You hold down the 2&8 keys while turning the machine on and wait for it to go into download mode...

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by nicknt82
    As you said " the engine does not respond to anything, only the power light is on." So how can you reload F/W ?

    If you can go on Service Mode, you can try reload F/W.

    ok thank you friend, so what steps should be taken?

    Leave a comment:


  • nicknt82
    replied
    Re: Canon iR2545

    Originally posted by purwoto
    Can it be solved with reload the system software?

    As you said " the engine does not respond to anything, only the power light is on." So how can you reload F/W ?

    If you can go on Service Mode, you can try reload F/W.

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by kuby
    I would try reloading firmware/software first.
    Yes, I will try it but where can I get the firmware.

    Leave a comment:


  • kuby
    replied
    Re: Canon iR2545

    I would try reloading firmware/software first.

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by nicknt82
    Clean RAM or replace new RAM. If's not solve, replace new Maincontroller PCB
    Can it be solved with reload the system software?

    Leave a comment:


  • nicknt82
    replied
    Re: Canon iR2545

    Originally posted by purwoto
    Hello All

    I have a problem with Canon IR2545,
    when the engine is turn on from the main switch, the engine does not respond to anything, only the power light is on. the engine will run after pressing the ON button in the control panel. even then the machine cannot be ready, only displays the progress bar. how to solve problems like this?

    Clean RAM or replace new RAM. If's not solve, replace new Maincontroller PCB

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by kuby
    Do you have a hard drive and system software to reload?


    What do you mean by hard drive? I have a laptop and cross cable to reload the system software, but I don't have the system software, do you want to share it with me?.

    Leave a comment:


  • kuby
    replied
    Re: Canon iR2545

    Do you have a hard drive and system software to reload?

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by kuby
    Did you try putting in another hard drive from a good machine?


    not yet, because the machine is only one.

    Leave a comment:


  • kuby
    replied
    Re: Canon iR2545

    Did you try putting in another hard drive from a good machine?

    Leave a comment:


  • purwoto
    replied
    Re: Canon iR2545

    Originally posted by yez
    have you clean RAM and ROM yet?
    yes, I've done it, but didn't solve anything.
    Last edited by purwoto; 03-14-2019, 09:40 AM.

    Leave a comment:


  • yez
    Guest replied
    Re: Canon iR2545

    have you clean RAM and ROM yet?

    Leave a comment:


  • purwoto
    started a topic [Misc] Canon iR2545

    Canon iR2545

    Hello All

    I have a problem with Canon IR2545,
    when the engine is turn on from the main switch, the engine does not respond to anything, only the power light is on. the engine will run after pressing the ON button in the control panel. even then the machine cannot be ready, only displays the progress bar. how to solve problems like this?
Working...