iR ADV C7065

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MrB
    Trusted Tech

    100+ Posts
    • Nov 2009
    • 147

    #1

    [Jamming] iR ADV C7065

    Got a bit of a strange one here that i would like to throw into the pan

    Constant 2 sided PJs from all 4 cassettes, But single sided is fine
    The device jams always at PS26 (Duplex tray) from all cassettes with a 0118 jam code

    I have changed both PS26 & PS25 sensors
    The I/O codes show that the sensors are working (P011 - bit 9 PS26 & bit 10 PS25) by changing 0 to 1 and back to 0
    Deck 2 single side works correctly through PS26

    The magnets and the catch plates for the duplex tray are okay and working
    Have replaced the 3 pressure block (& springs) on the unit and also changed the 2 that forces the try up into the unit but still jams
    Any Ideas please will be Grateful

    Thanks
    70xx PP.jpg
  • teckat
    Field Supervisor

    Site Contributor
    10,000+ Posts
    • Jan 2010
    • 16083

    #2
    Re: iR ADV C7065

    Originally posted by MrB
    Got a bit of a strange one here that i would like to throw into the pan

    Constant 2 sided PJs from all 4 cassettes, But single sided is fine
    The device jams always at PS26 (Duplex tray) from all cassettes with a 0118 jam code

    I have changed both PS26 & PS25 sensors
    The I/O codes show that the sensors are working (P011 - bit 9 PS26 & bit 10 PS25) by changing 0 to 1 and back to 0
    Deck 2 single side works correctly through PS26

    The magnets and the catch plates for the duplex tray are okay and working
    Have replaced the 3 pressure block (& springs) on the unit and also changed the 2 that forces the try up into the unit but still jams
    Any Ideas please will be Grateful

    Thanks
    [ATTACH=CONFIG]26866[/ATTACH]

    -------------------------------------------------------------

    -check if duplex tray jam roller is extremely difficult to turn ? > if so >clean & lube>then check
    if it turns manually , but does not turn when duplexing> a bad fixing feed driver pcb can be issue

    -clean duplex path rollers
    ? last resort-Reverse Paper Delivery Assembly (FM3-4756-000)
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

    Comment

    • MrB
      Trusted Tech

      100+ Posts
      • Nov 2009
      • 147

      #3
      Re: iR ADV C7065

      Just to keep people updateed (If you are interested)

      Did try a new reversal assy, No good, lasred 4 pages



      This issue was fixed by replacing the "Fixing/Feeding Lock Assy"

      It sits at the front of the device, and is where the process unit latches onto when pushed back in

      (When you pull the unit out, look at the front middle, it has a spring loaded gear on it, also has a shaft with a blue gear the is bushed into it)

      Well replaced that part, ran shed loads through it, started the car as i couldnt get out quick enough


      Fig 105 Item 18 - FM3-9915-000 FIXING/FEEDER LOCK ASSEMBLY

      Comment

      • teckat
        Field Supervisor

        Site Contributor
        10,000+ Posts
        • Jan 2010
        • 16083

        #4
        Re: iR ADV C7065

        Originally posted by MrB
        Just to keep people updateed (If you are interested)

        Did try a new reversal assy, No good, lasred 4 pages



        This issue was fixed by replacing the "Fixing/Feeding Lock Assy"

        It sits at the front of the device, and is where the process unit latches onto when pushed back in

        (When you pull the unit out, look at the front middle, it has a spring loaded gear on it, also has a shaft with a blue gear the is bushed into it)

        Well replaced that part, ran shed loads through it, started the car as i couldnt get out quick enough


        Fig 105 Item 18 - FM3-9915-000 FIXING/FEEDER LOCK ASSEMBLY

        -----------------------------------------------------------------------------------------------------------

        "EXCELLENT"
        **Knowledge is time consuming, exhausting and costly for a trained Tech.**

        Comment

        • Benjamin98
          Technician

          50+ Posts
          • Mar 2015
          • 89

          #5
          Re: iR ADV C7065

          Originally posted by MrB
          Just to keep people updateed (If you are interested)

          Did try a new reversal assy, No good, lasred 4 pages



          This issue was fixed by replacing the "Fixing/Feeding Lock Assy"

          It sits at the front of the device, and is where the process unit latches onto when pushed back in

          (When you pull the unit out, look at the front middle, it has a spring loaded gear on it, also has a shaft with a blue gear the is bushed into it)

          Well replaced that part, ran shed loads through it, started the car as i couldnt get out quick enough


          Fig 105 Item 18 - FM3-9915-000 FIXING/FEEDER LOCK ASSEMBLY

          Hi there,

          Just looking at your post above, how did you figure it was the Fixing/Feeder Lock Assembly??

          Reason I ask, is I have the exact same issue on a IPR C600i. Have done the necessary fault findings...sensors and motors all check out. Machine still constantly jams ONLY on Duplex.

          If you can remember, I would be so grateful!

          Ben

          Comment

          Working...