Konica Minolta Bizhub C252 - no network menu

[mx6turbo89]

Re: Konica Minolta Bizhub C252 - no network menu

So, I tried to reset NVRAM, but I got this blank screen:


Then I tried to upload firmware which for c252:


then I clicked start...

Now I have C-C163 error...

C250 firmware must be updated in the correct order or else you'll get that error. Install this earlier firmware to get your machine back up: https://www.dropbox.com/s/m23xclappq...-133A.EXE?dl=0

[zlobuch]

Re: Konica Minolta Bizhub C252 - no network menu

So, I tried to reset NVRAM, but I got this blank screen:

[ATTACH=CONFIG]35615[/ATTACH]

Then I tried to upload firmware which for c252:

[ATTACH=CONFIG]35616[/ATTACH]

then I clicked start...

Now I have C-C163 error...

[mx6turbo89]

Re: Konica Minolta Bizhub C252 - no network menu

I have exactly the same problem, but on bizhub C250. Could anybody send me firmware and NVRAM reset on bizhub c250?

The C250 NVRAM reset firmware is the same as for a C252, so you can get it at the link I posted.

[Synthohol]

Re: Konica Minolta Bizhub C252 - no network menu

I have exactly the same problem, but on bizhub C250. Could anybody send me firmware and NVRAM reset on bizhub c250?

ya might want to start your own thread, hitchhiking this one may not get all the responses you need.

[zlobuch]

Re: Konica Minolta Bizhub C252 - no network menu

I have exactly the same problem, but on bizhub C250. Could anybody send me firmware and NVRAM reset on bizhub c250?

[mx6turbo89]

Re: Konica Minolta Bizhub C252 - no network menu

Unfortunately, any of methods mentioned above (except NVRam reset) didn't work, the problem is still there. Thank you very much for sending me firmware file, I wil try to flash it on Monday, maybe it will work. My last request (I promise ), could you send me, if possible, NVRam reset firmware?

NVRAM reset firmware: https://www.dropbox.com/s/nd3bcrjkho...4-000.EXE?dl=0

[michal7778]

Re: Konica Minolta Bizhub C252 - no network menu

Unfortunately, any of methods mentioned above (except NVRam reset) didn't work, the problem is still there. Thank you very much for sending me firmware file, I wil try to flash it on Monday, maybe it will work. My last request (I promise ), could you send me, if possible, NVRam reset firmware?

[mx6turbo89]

Re: Konica Minolta Bizhub C252 - no network menu

Ok, I will check if HDD is set to "Installed".
I have Konica Imaging Toolkit but i can't find firmware file anywhere. Could anybody send me this file?

Firmware: https://www.dropbox.com/s/l5fqprubrp...-A959.EXE?dl=0

[michal7778]

Re: Konica Minolta Bizhub C252 - no network menu

Ok, I will check if HDD is set to "Installed".
I have Konica Imaging Toolkit but i can't find firmware file anywhere. Could anybody send me this file?

[patk]

Re: Konica Minolta Bizhub C252 - no network menu

Had this before. Before you reset anything, check that HDD is set to Installed in System 2 >HDD.

Ive had this occur on C252 as a result of a power outage

Cheers

[habik]

Re: Konica Minolta Bizhub C252 - no network menu

I'm sorry. I can't pass you the NVRAM firmware. And yes you are correct. Put it on flash card (I use 256MB) through utility Konica Imaging toolkit v2.54 I think is the latest)
So 3 things you need.
Someone already posyed the toolkit on here not a while ago.



Byting on bits.

[michal7778]

Re: Konica Minolta Bizhub C252 - no network menu

Thank you for the replies (and patience ).
Now I understand almost everything except one thing. I assume that NVRam reset firmware is a file that I need to put on CF card and than run the copier, am I right? If so, the only problem is that I don't have an acces to NVRAM reset firmware for this machine, could you please send it to me, maybe using PM?
I will also be grateful for normal firmware file, so as to perform an update.
I don't want to start whole repair procedure without being fully prepared.
I'm sorry for (too) many questions but this is the first time I've had such an issue.

[Copier Addict]

Re: Konica Minolta Bizhub C252 - no network menu

Thanks for all proposed solutions. I'm unable to log in via browser, I can see only blank page.
The machine was also powered on for few hours, the tab didn't appear.
I will try to perform NIC reset.
If it won't work than I will have to perform whole iniialization procedure. However, for me this is the last posibble option, I don't want to calibrate everything once again.
Where exactly is the NIC reset option located in the Service Mode menu?
What about flashing new firmware, maybe it will solve the problem?

If you read the bulletin, it states to do the data clear first. A data clear does not initialize the NVRam. If data clear does not work, then do the NIC clear THEN if both of those don't work, do the MVRam initialize.
Before doing any of the above, back up the address book if possible.

[habik]

Re: Konica Minolta Bizhub C252 - no network menu

Thanks for all proposed solutions. I'm unable to log in via browser, I can see only blank page.
The machine was also powered on for few hours, the tab didn't appear.
I will try to perform NIC reset.
If it won't work than I will have to perform whole iniialization procedure. However, for me this is the last posibble option, I don't want to calibrate everything once again.
Where exactly is the NIC reset option located in the Service Mode menu?
What about flashing new firmware, maybe it will solve the problem?

Re-read paragraf 2 a. It explains it where the NIC reset is. You will need NVRAM reset firmware which contains the NIC reset. When you load it it will give you two options on screen:

NIC

NVRAM RESET

you pick the one you need.

Good luck.

[michal7778]

Re: Konica Minolta Bizhub C252 - no network menu

Thanks for all proposed solutions. I'm unable to log in via browser, I can see only blank page.
The machine was also powered on for few hours, the tab didn't appear.
I will try to perform NIC reset.
If it won't work than I will have to perform whole iniialization procedure. However, for me this is the last posibble option, I don't want to calibrate everything once again.
Where exactly is the NIC reset option located in the Service Mode menu?
What about flashing new firmware, maybe it will solve the problem?