I have few Konica Minolta bizhub 4750 printers and on all of them I have error code E301(000.00) as soon as i plug in network to it. Anyone had problem like that?
-
Last edited by serzhmarchuk; 07-31-2020, 11:35 PM. -
Re: Konica Minolta bizhub 475 error code E301
E301 Referring incorrect memory
reseat the ram or maybe if the additional ram is the wrong type?
if not the copier then maybe the wrong driver is being used to print?
Konica is down so i cant even get a solution if one exists.
We know a thing or two because we've seen a thing or two.
The medication helps though... -
Re: Konica Minolta bizhub 475 error code E301
Go Admin setting>Network>SSDP ? Broadcasting? > Disable it.
Works on xx4 seriesComment
-
Re: Konica Minolta bizhub 475 error code E301
I'm just going to say that I wish you luck. We placed (4) bizhub 4052's that lock up the moment they are plugged into the endusers network. They do not lock up on our network, or any other network tested. If there is a solution, KM could not come up with it.
If my opinion carries any weight (and it usually does not) it seems like the only feasible solution to substitute Lexmarks. Yes, I know it's basically the same engine, but the Lexies don't lock up.
I'll be watching the comments. =^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: Konica Minolta bizhub 475 error code E301
blackcat4866,
With ALL due respect Sir I strongly DISAGREE with this statement
I Consider YOU Sir, one of the MOST on point users with your recommendations .. You Sir, have a knowledge I only wish I could attain ..
PLEASE Brother NEVER sell yourself short in any way shape or form. I know you are a humble soul.. but don't sell yourself short.
Phil B.Comment
-
Re: Konica Minolta bizhub 475 error code E301
turn on the machine with the network cable unplugged.
if it starts up fine, clear the print queue.
make sure it is running the latest firmware, there are a plethora of print job related bugs that cause this.Comment
-
Re: Konica Minolta bizhub 475 error code E301
We had a couple of 4750s doing this. Never did find a fix. KM couldn't figure it out. Installed different machines for the customer and all is well. Put the 4750s in another location. small companies. working okComment
-
Re: Konica Minolta bizhub 475 error code E301
Hi, the bizhub 4050/4750 is the first start of Konica Minolta software integration into Lexmark. If you notice, the settings are similar to Konica Minolta printers but I personally consider a bad copy bad. A good integration of the Konica Minolta software I found it only in the next model, therefore in bizhub 4052.
I have seen several bulletins on network problems and E301/E304. The best advice is to update the firmware to the latest version. I have seen several bulletins on network problems and E301. The best advice is to update the firmware to the latest version. Another bulletin suggests "Change the network speed setting to automatic. (Default: 100 Mbps half duplex)"
Other solution:
1. Install the firmware that fixes the issue.
2. Change to [ON] if [Rank C] of [Internal Error. Auto Cancel] in Service menu is set to [OFF].
Procedures: [Service Mode]> [System 2]> [Internal Error. Auto Cancel]> [Rank C]
Change to [ON] if it's set to [OFF]. (Default: ON)
Supplementary information:
The interval time from Error occurrence to automatic reboot can be changed by the following Software Switch setting.
291 bit0: [0]: 60 seconds to automatic reboot. (Default)
[1]: 10 seconds to automatic reboot.
[Fixed firmware]
bizhub 4750/4050
-> Install A6F730G0705-W99, A6F730G0705-999, or later.Comment
-
Re: Konica Minolta bizhub 475 error code E301
Thanks, it always starts up fine without network cable attached. in fact it works fine on USB only.
Anyway, Do you know how to update firmware on it if there is service password that is not default and I don't know a new one?
Comment
-
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Re: Konica Minolta bizhub 475 error code E301
Actually I do have the service password it actually was the default one. However, no manual can tell me how to upgrade the firmware. I assume its only for the authorized personal, butpprinter is used and out of warrranty, i thought may be tehre is a way to update it myself.Comment
-
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Comment
-
Re: Konica Minolta bizhub 475 error code E301
Its actually default password, i was entering it wrong. But there is no firmware upgrade option in service mode. I understand kinoca minolta is different from Lexmark on this issue, but is there a way to do it yourself?
Comment
Comment