Konica Software Switch settings (complete)

[NN-GG]

Time to go to the MFP control panel. Not available from web connection sorry.

1748586047134.jpg

I was helping the customer remotely. I was thinking I could do it by the port 50443 remote panel, but I guess that's not good enough, too. Will try it on the copier itself sometime.

[tsbservice]

With new Oauth 2.0 for email, wondering why this can't show up. Not sure if this is related to the function version or Software Switch settings?


At C361i panel & webui:

"Item cannot be displayed in current settings"


Oauth2.0 can't display.png

Time to go to the MFP control panel. Not available from web connection sorry.

1748586047134.jpg

[NN-GG]

With new Oauth 2.0 for email, wondering why this can't show up. Not sure if this is related to the function version or Software Switch settings?


At C361i panel & webui:

"Item cannot be displayed in current settings"


Oauth2.0 can't display.png

[DeWalt_Man]

Re: Konica Software Switch settings (complete)

Bizhub C650i that wont allow a keyboard to pop up when trying to enter a IP address? You can enter Admin. but once in you cant get to the keyboard, its non-existent. Could this be some type of security done through the soft switches? There is no extra programs added and the all clear has been done numerous times, FW reloaded and the machine wont find the network on its own. Any ideas?

its not a setting issue, ironically
had this before, it thinks theres a keyboard installed, probs a card reader below the control panel / screen

[Wakawaka]

Hey everyone, I have a government agency that requires that the PDF version that the Konica Minolta i series sends (via email) be at version 1.5 or higher, currently the machines I've tested are at 1.4, however I do happen to have one machine in the field (C550i) that apparently sends version 1.6. (machine is out of town, haven't looked at it directly yet) KM Support said SW43 set to HEX 20 should change the version that it sends, however on every i series machine that I've tested, it won't take HEX 20. KM confirmed that this switch should change the version but they also had issues changing it on their end on their i series copier. current firmware is g00-re. Has anyone else come across this and does anyone have any insight?

[zayonc]

A new software switch is implemented to change the behavior.:

DipSW No. 174 bit 1: Change the time of starting the next job.

0x00: Disable (default) - Prepare to start the next job when the last page of the previous job is fed.

0x02: Enable - Prepare to start the next job when printing information of the last page of the previous job is prepared.

[systemnova]

Any guesses what DipSW 189 Bit 1 does?
The "V2" FUM algorithm does?
Fumbling Under Machinery?

[D Colour]

I know..old post..Does anyone have info on softswitch 217.. This supposedly corrects a false 100% toner issue when the bottle is empty..The KM kb article says set "DIPSSW" 217 to 0x02..I think this means set it to HEX02 but I am not 100%..

Emujo

This is from Blackcat's book of tricks.

image.png

The 8 series onwards has an engine fw dipswitch to reset toner level to 100%. If it wasnt detected when replaced.

image.png

[emujo2]

I know..old post..Does anyone have info on softswitch 217.. This supposedly corrects a false 100% toner issue when the bottle is empty..The KM kb article says set "DIPSSW" 217 to 0x02..I think this means set it to HEX02 but I am not 100%..

[tsbservice]

Re: Konica Software Switch settings (complete)

What is the switch to lock user settings behind admin password

Try DIP switch 200 set to HEX 20.

[rrrohan]

Re: Konica Software Switch settings (complete)

What is the switch to lock user settings behind admin password

[mitchl]

Re: Konica Software Switch settings (complete)

Bizhub C650i that wont allow a keyboard to pop up when trying to enter a IP address? You can enter Admin. but once in you cant get to the keyboard, its non-existent. Could this be some type of security done through the soft switches? There is no extra programs added and the all clear has been done numerous times, FW reloaded and the machine wont find the network on its own. Any ideas?

[KMFLT3CH]

Re: Konica Software Switch settings (complete)

Switch 153, HEX 40 on the I-series has been invaluable.

[astanbr85]

Re: Konica Software Switch settings (complete)

Hi,

can anyone tell me what 153 and 240 is (and possible values & meanings)?

Thank you!

I believe on an I-series machine, SW 153 this changes the colour reproduction. Hex 40 changes it to IT5 colour, Hex 00 is the default IT6 colour. I think this was covered by someone else further back that had an example attached to it as well.

[jotunn]

Re: Konica Software Switch settings (complete)

What are the current settings of these DipSW and why do you think they are not the default?

The default setting is a matter of convention - Konica Minolta always changes the factory settings when delivering machines to customers under contract, so the new setting is the default for contract machines.