Knick on the fuder sleeve

[positiveg]

Good day all. Hope everyone is safe and well.
I've got this knick on the fuser sleeve. Pretty small but it shows up on he print in the most strange areas. Well most prints especially when we're doing booklets. Is there anyway to change the roller or sleeve on this KM C454e?
Please let me know this fiser has less than 50k clicks
Thanks again

Sent from my SM-G955F using Tapatalk

[patrickjlc]

Re: Knick on the fuder sleeve

I have replaced rollers on kyocera machines, since they are available. but on c454 you may have to get a whole fuser unit. Unless you know how to get them apart and rebuild them.....

Sent from my motorola one 5G UW using Tapatalk

[copier tech]

Re: Knick on the fuder sleeve

Good day all. Hope everyone is safe and well.
I've got this knick on the fuser sleeve. Pretty small but it shows up on he print in the most strange areas. Well most prints especially when we're doing booklets. Is there anyway to change the roller or sleeve on this KM C454e?
Please let me know this fiser has less than 50k clicks
Thanks again

Sent from my SM-G955F using Tapatalk

I have a new c454e fuser for sale should you need one.

[copyman]

Re: Knick on the fuder sleeve

Good day all. Hope everyone is safe and well.
I've got this knick on the fuser sleeve. Pretty small but it shows up on he print in the most strange areas. Well most prints especially when we're doing booklets. Is there anyway to change the roller or sleeve on this KM C454e?
Please let me know this fiser has less than 50k clicks
Thanks again

Sent from my SM-G955F using Tapatalk

They sell aftermarket fuser sleeves & rollers. The sleeve is same as C224 & 4 series. The C454 & C454e uses a different lower roller but sleeve is same. Sleeve cost around $50. Takes a few hours to rebuild the fuser first time doing it.

This was discussed a lot here: Bizhub C224e/C258 series fuser premature failure

[blazebusiness]

Re: Knick on the fuder sleeve

Good day all. Hope everyone is safe and well.
I've got this knick on the fuser sleeve. Pretty small but it shows up on he print in the most strange areas. Well most prints especially when we're doing booklets. Is there anyway to change the roller or sleeve on this KM C454e?
Please let me know this fiser has less than 50k clicks
Thanks again

Sent from my SM-G955F using Tapatalk

I prefer to just replace the whole fuser and avoid the risk of something going wrong rebuilding these. But 50K is a very low click count on that fuser so , if money is an issue, they do sell aftermarket sleeves. Not sure if you can get them or who you use for parts on your island.

[emujo2]

Re: Knick on the fuder sleeve

I just coudn't wait to see what Knick on the fuder sleeve was all about. lol

[blazebusiness]

Re: Knick on the fuder sleeve

I just coudn't wait to see what Knick on the fuder sleeve was all about. lol

Yes, at first I was concerned he was referring to a body part. Sounded extremely painful.

[Bix]

Re: Knick on the fuder sleeve

Hey, make sure the filter is clean. Alternatively, replace the toner filter
In some cases, they may cause toner to build up and damage consumables.
(accumulation of toner)

[patrickjlc]

Re: Knick on the fuder sleeve

I would get another fuser while you rebuild this one. Depending on how long it takes to get the parts...

Sent from my motorola one 5G UW using Tapatalk

[mga]

Re: Knick on the fuder sleeve

Good day all. Hope everyone is safe and well.
I've got this knick on the fuser sleeve. Pretty small but it shows up on he print in the most strange areas. Well most prints especially when we're doing booklets. Is there anyway to change the roller or sleeve on this KM C454e?
Please let me know this fiser has less than 50k clicks
Thanks again

Sent from my SM-G955F using Tapatalk

That looks like a compatible part try to only use oem the cheap China parts are rubbish

[blazebusiness]

Re: Knick on the fuder sleeve

That looks like a compatible part try to only use oem the cheap China parts are rubbish

We stock those brand new OEM fuser units. That sure looks like the OEM Konica sleeve to me.

[positiveg]

Re: Knick on the fuder sleeve

We stock those brand new OEM fuser units. That sure looks like the OEM Konica sleeve to me.

So where can I get it?

Sent from my SM-G955F using Tapatalk