i would like to now, how can i solve this code error c-6702 ? this code error appear when i change the developing unit and developer. help me i need solution.
konica minolta biz500 (code error c-6702 )
Collapse
X
-
Tags: 2803, abnormality, act, c-2803, connections, exposure, konicaminolta, lef, oacb, pressed, release
-
Error C-6702
AGC abnormality.
AGC counter overflow
Involved parts:
CCD board (CCDB)
Exposure lamp (L1)
L1 inverter (L1 INVVB)
Scanner motor (M2)
Overall control board (OACB)
First off I'd try a trouble reset
1. Turn ON the main power switch (SW1).
2. With the Utility/Counter key pressed, turn ON the power switch (SW2).
3. Press [Trouble reset] to release a trouble with [OK] displayed.
4. Turn OFF and ON the power switch (SW2). -
baggio
konica minolta biz500 ( code error c-6702 )
i try to make a trouble reset ( turn off the machine swithc 1, then press the utility key,turn on de power switch 1 ), the machine doesn`t work. i don`t have a solution.Comment
-
baggio
-
baggio
konica minolta code error c-2803
i find this code error c-2803, when i try to make a tcr adjust,. i need solution. i change the developing unit and developer.Comment
-
turn off the copier. Hold down the utility key and turn copier back on (still press utility key until Konicaminolta sign appear) trouble reset will come up. Press trouble reset. DONT TURN COPIER OFF Then go into techrep mode and do TCR When finished turn off. With any luck you should be able to leave client and have coffee . . .Comment
-
here are some solutions...
Description"Now Warming" displays if the machine is turned on with the right door open. When the door is then closed "Warming Up" stays on the screen. The fuser iswarm. If all
CAUSE: 2000 sheet LCT connections wires in connector are loose.SOLUTION: Resolder connector wires or replace harness (p/n 4348 6801 02).
DescriptionC-6701 (C6701) or C-6702 (C6702) at power up. TheMFP scans to home position and the exposure lamp lights. If code is indicated during copy cycle, copiesmay be all black.
SolutionPROBABLE CAUSES:functioning properly.
1.Failed Overall Control Board (OACB).
Check ICP3 on the OACB. If it is OPEN, checkfor shorts andreplace the Overall CB (p/n50GA -930 4M for bizhub 360/420/500 and p/n A0R5 H010 06 for
bizhub 361/421/501 ).
2.A communication issue between the CCD and OACB. Thisissue usually appears shortly after replacing or removing the OACB (Overall Control Board).
Please check the flat cable between the CCD and OACB. Make sure it is undamaged and connected properly. Replace the CCD cable (p/n 50GA 9050 0)if
reseating it has no effect on the service code.
3. During start up the CCD sensor is not initializing properly. Light from the exposure lamp is not being reflected by the white patch located under the platen
glass to the CCD sensor via the optics.
Make sure the optics is intact and positioned properly. Make sure the platen glass is also placed properly. The CCD also should be connected properly and
positioned properly. Be sure the cover for the CCD assembly is mounted correctly. Replace the CCD (p/n 50GA -626 1) if the optics and exposure system are
DescriptionC-6702 (C6702) shortly after power up.SolutionPROBABLE CAUSES:Check ICP2 on the CCD board. If it is open, check for shorts and replace the CCDunit (p/n 50GA -626 1).
1. The Overall Control Board/System Control Board has failed.
Replace the failed Overall Control Board/System Control Board (p/n 50GA-930 1H).
2. The CCD Board has failed.
Comment
Comment