How to replace the fuser unit of KONICA MINOLTA BizHub C351?

[mrwho]

Stupid question: Are you specifying the correct paper size in the tray, or is it being detected correctly?

[maynard]

sounds like a sensor. if it stops in the exact same place every time. I don't have a machine in front of me. but there must be a sensor in the exit section. I will look over my book tomorrow if I get a chance. mabee I will fly down and fix it for you..

later
brent

thank you brent. i don't have money to pay you that's why i'm tryin' to fix it by myself

[brent]

sounds like a sensor. if it stops in the exact same place every time. I don't have a machine in front of me. but there must be a sensor in the exit section. I will look over my book tomorrow if I get a chance. mabee I will fly down and fix it for you..

later
brent

[maynard]

I have several of these out. but only have a c350 here with me in the office. have you tried to see if there is anything stuck in the paper path? does the paper just stop. or it is accordianed in that black piece above the fuser?

There's nothing or any blockage in the paper path. The paper always stop after the half of it appeared.

[brent]

I have several of these out. but only have a c350 here with me in the office. have you tried to see if there is anything stuck in the paper path? does the paper just stop. or it is accordianed in that black piece above the fuser?

[maynard]

not to be too rude. but you probably didn't save any money on this . since you bought a fusing unit and tried to do it yourself. now you pretty much need to call a technician..a question for you. do you have a finisher on your machine? I had the actuator break on of my horizontal transport assemblies. that will jam the machine. the actuator is formed onto a guide. when that unit breaks the paper just stops after the fuser

I don't have finisher. I attached a picture so you can see it clearly. Thanks Brent
C351.JPG

[brent]

not to be too rude. but you probably didn't save any money on this . since you bought a fusing unit and tried to do it yourself. now you pretty much need to call a technician..a question for you. do you have a finisher on your machine? I had the actuator break on of my horizontal transport assemblies. that will jam the machine. the actuator is formed onto a guide. when that unit breaks the paper just stops after the fuser

[JustManuals]

Not me. I'm not a copier tech.

[maynard]

[QUOTE=manuals4you;220009][B][COLOR=navy]This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from
Just Manuals | The Internet's largest selection of manuals | Instant Downloads


I just got the Service Manual and checking the Paper Exit Drive Section and Paper Transport Section. Are you familiar with this problem? Thanks Paul

[JustManuals]

This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from
Just Manuals | The Internet's largest selection of manuals | Instant Downloads


Paul@justmanuals.com

[maynard]

The first thing is to make sure the fuser connectors are well inserted and the fuser is well positioned and receiving movement from the machine.

The fuser is well inserted and connected. The paper is coming out from the fuser and just stay there coz it can't go to the next part which is next to fusing assembly, that's why there's a paper jam.

[mrwho]

The first thing is to make sure the fuser connectors are well inserted and the fuser is well positioned and receiving movement from the machine.

[maynard]

I replaced the fusing assembly successfully but still I got paper jam error. The paper only stays on the fusing assembly, can't go thru to the next part. I'm thinking I need also to replace the next part after fusing assembly. Any idea, gentlemen? I need your help. Thanks guys

[maynard]

This may help. It isn't very hard.

ah okay. thank you. it gives me an idea where that cable go through

[dogsbody]

This may help. It isn't very hard.

If you are going to post at least make sure it is for the right machine, that is C203/253/353. C351 is a slower C450 nothing like what you have described.

As the others have said it is not hard to change the fuser, a couple of screws and three plugs if you can't figure it out buy a manual or call a tech