Bizhub C452 - background in one corner [scanning from flatbed]

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • -ph-
    Technician
    • Jun 2009
    • 30
    #1

    Bizhub C452 - background in one corner [scanning from flatbed]

    Hi,

    This afternoon I ran into this problem, when making an A3 scan from flatbed there's one corner with background [the corner nearest to the operating panel] if I make the same scan from the feeder I have no background. The feeder closes correctly, I checked and cleaned the optics and ran through stabilisation and grad. adjust, but no result.

    check image below:

    background bh c452 - A3.jpg

    any ideas?
    Tags: reject
    • mrwho
      Major Asshole!

      Site Contributor
      2,500+ Posts
      • Apr 2009
      • 4299
      #2
      Re: Bizhub C452 - background in one corner [scanning from flatbed]

      Bent scanner. Someone's been leaning over it while taking copies.
      ' "But the salesman said . . ." The salesman's an asshole!'
      Mascan42

      'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'
      Ibid

      I'm just an ex-tech lurking around and spreading disinformation!

        Comment

        • EarthKmTech
          Step aside, noob

          1,000+ Posts
          • May 2009
          • 2139
          #3
          Re: Bizhub C452 - background in one corner [scanning from flatbed]

          yep, seen this before. I agree with mrwho.

          Or if its a new machine, its been damaged in transit and I'd write it off or reject it.

            Comment

            • -ph-
              Technician
              • Jun 2009
              • 30
              #4
              Re: Bizhub C452 - background in one corner [scanning from flatbed]

              Thanks for the response, i'll try to bend, hope it will work out.

                Comment

                • blackcat4866
                  Master Of The Obvious

                  Site Contributor
                  10,000+ Posts
                  • Jul 2007
                  • 22946
                  #5
                  Re: Bizhub C452 - background in one corner [scanning from flatbed]

                  Originally posted by mrwho
                  Bent scanner. Someone's been leaning over it while taking copies.
                  Ditto that. Until you get it focussed properly it won't complete gradation. =^..^=
                  If you'd like a serious answer to your request:
                  1) demonstrate that you've read the manual
                  2) demonstrate that you made some attempt to fix it.
                  3) if you're going to ask about jams include the jam code.
                  4) if you're going to ask about an error code include the error code.
                  5) You are the person onsite. Only you can make observations.

                  blackcat: Master Of The Obvious =^..^=

                    Comment

                    • BennyAU
                      Technician
                      • Dec 2012
                      • 25
                      #6
                      Re: Bizhub C452 - background in one corner [scanning from flatbed]

                      had one of these machines do the same thing at run-up
                      tried replacing ccd unit, all associated cabling, none of it worked
                      didnt check the framework, but we just sent the machine back and got a replacement.

                      for your sake, i hope its not a field machine, because i wouldn't want to have to replace the framework

                        Comment

                        • -ph-
                          Technician
                          • Jun 2009
                          • 30
                          #7
                          Re: Bizhub C452 - background in one corner [scanning from flatbed]

                          problem solved, it was just a matter of bending the scanner back in its correct position, trail and error, luyckily it was pretty easy.

                            Comment

                            • mrwho
                              Major Asshole!

                              Site Contributor
                              2,500+ Posts
                              • Apr 2009
                              • 4299
                              #8
                              Re: Bizhub C452 - background in one corner [scanning from flatbed]

                              Originally posted by -ph-
                              problem solved, it was just a matter of bending the scanner back in its correct position, trail and error, luyckily it was pretty easy.
                              Thanks for the input! Reps to you!
                              ' "But the salesman said . . ." The salesman's an asshole!'
                              Mascan42

                              'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'
                              Ibid

                              I'm just an ex-tech lurking around and spreading disinformation!

                                Comment

                                • EarthKmTech
                                  Step aside, noob

                                  1,000+ Posts
                                  • May 2009
                                  • 2139
                                  #9
                                  Re: Bizhub C452 - background in one corner [scanning from flatbed]

                                  We've had a nutter sit down and graft the top end of one scrap machine onto a field machine, it wasn't actually that hard but just quite a bit of time required.

                                    Comment

                                    Previous template Next
                                    Working...