Taskalfa 181/221

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Realtech
    Trusted Tech
    100+ Posts
    • Oct 2009
    • 103
    #1

    Taskalfa 181/221

    Two days ago I installed a new Taskalfa 221 the next day the customer complaint when they copy document from the DP or platen glass a black vertical lines appear on paper.
    When they fax document customer received vertical black lines on the document too.
    So I when there to make sure the CVT glass and the platen glass are clean I notice that it happened intermittent any idea?
    Tags: black, complaint, copy, customer, document, glass, intermittent, lines, paper, received, taskalfa
    • Jules Winfield
      Senior Tech

      500+ Posts
      • Jul 2009
      • 823
      #2
      Check/clean the main charge unit...
      But I'm trying, Ringo. I'm trying real hard... to be the Shepherd.

        Comment

        • blackcat4866
          Master Of The Obvious

          Site Contributor
          10,000+ Posts
          • Jul 2007
          • 22741
          #3
          I'd clean the slit glass with alcohol, just in case you missed a speck. I'd also check that the shading plate is clean.

          Does it have one of those black mylars on the top surface of the slit glass? It may need to be re-positioned. If it's still happening, you can adjust the shading position. =^..^=
          If you'd like a serious answer to your request:
          1) demonstrate that you've read the manual
          2) demonstrate that you made some attempt to fix it.
          3) if you're going to ask about jams include the jam code.
          4) if you're going to ask about an error code include the error code.
          5) You are the person onsite. Only you can make observations.

          blackcat: Master Of The Obvious =^..^=

            Comment

            • madas
              Trusted Tech

              250+ Posts
              • Aug 2008
              • 313
              #4
              I agree with blackcat, clean the slit glass again. line up the copy on the glass which shows the line and look at the glass at an angle ie, crouch down a bit.
              I had similar long ago cleaned slit glass and it looked spot less but produced a line. when I used the copy as a guide and looked at an angle I could see the problem.
              Also make sure there is no fluff or something under or on the edge of the glass! if it is intermittent sounds possible something is getting moved into the paper path.

              madas

                Comment

                • ss200222
                  Technician
                  • Jan 2012
                  • 21
                  #5
                  Re: Taskalfa 180

                  Hi, am new to this forum, can anyone help me with the network printing for Taskalfa 180?

                    Comment

                    • blackcat4866
                      Master Of The Obvious

                      Site Contributor
                      10,000+ Posts
                      • Jul 2007
                      • 22741
                      #6
                      Re: Taskalfa 181/221

                      Here's my suggestion:
                      Go to the Forum tab > Kyocera > Start A New Thread > then start a new thread.
                      When you're composing the thread it's a good idea to tell us exactly what you've done, and what settings you're using so we can provide a semi-informed response.

                      "It don't work! Help! Help! Help!" won't get you very far. =^..^=
                      If you'd like a serious answer to your request:
                      1) demonstrate that you've read the manual
                      2) demonstrate that you made some attempt to fix it.
                      3) if you're going to ask about jams include the jam code.
                      4) if you're going to ask about an error code include the error code.
                      5) You are the person onsite. Only you can make observations.

                      blackcat: Master Of The Obvious =^..^=

                        Comment

                        • Geo
                          Senior Tech

                          500+ Posts
                          • Nov 2010
                          • 660
                          #7
                          Re: Taskalfa 181/221

                          Originally posted by blackcat4866
                          Here's my suggestion:
                          Go to the Forum tab > Kyocera > Start A New Thread > then start a new thread.
                          When you're composing the thread it's a good idea to tell us exactly what you've done, and what settings you're using so we can provide a semi-informed response.

                          "It don't work! Help! Help! Help!" won't get you very far. =^..^=
                          Blackcat...does PLEASE HHHHEEEEEEELLLLLLLLLLLPPPP!!!!! work any better..

                            Comment

                            • blackcat4866
                              Master Of The Obvious

                              Site Contributor
                              10,000+ Posts
                              • Jul 2007
                              • 22741
                              #8
                              Re: Taskalfa 181/221

                              Give me that M16 rifle ... =^..^=
                              If you'd like a serious answer to your request:
                              1) demonstrate that you've read the manual
                              2) demonstrate that you made some attempt to fix it.
                              3) if you're going to ask about jams include the jam code.
                              4) if you're going to ask about an error code include the error code.
                              5) You are the person onsite. Only you can make observations.

                              blackcat: Master Of The Obvious =^..^=

                                Comment

                                • Venom
                                  Technical/IT Support

                                  500+ Posts
                                  • Nov 2009
                                  • 765
                                  #9
                                  Re: Taskalfa 181/221

                                  I have seen a few times, the doc feed skew needs to be adjusted. The doc feed gets pulled on when machines are moved. There is one screw on right hinge that you can access when doc feed is up, loosen and adjust.
                                  IBM, Mita, Konica Minolta, Ricoh, Kyocera, HyPAS, Canon, Oce, Samsung, HP, TEO IP PBX/Unified Communications, Comptia Network+ Comptia PDI+ Certifications

                                    Comment

                                    Previous template Next
                                    Working...