power problems concerning MX-7500

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • dwarf
    Trusted Tech

    100+ Posts
    • Oct 2012
    • 168
    #1

    [Electrical] power problems concerning MX-7500

    we have a customer who experiences a lot of electrical power problems in their building...can somebody offer a recommendation for the proper type of voltage regulator we should steer them towards?... here is what the manual says about power requirements...

    200 V (North America, etc.) 200 V (Europe, etc.)
    Maximum rated power Consumption*1 2880W 3840W
    Energy consumption rate Not applicable
    TEC value (Measured result) 65cpm machine 8.1kWh Now Measuring
    75cpm machine 9.1kWh Now Measuring
    TEC value (Standard) Tier2 65cpm machine 20.5kWh (0.70kwh * 65 - 25.0 kwh)
    75cpm machine 27.5kWh (0.70kwh * 75 - 25.0 kwh)
    Network/Fax waiting power consumption: 1W or less
    * The network protocol is TCP/IP only.
    No
    Moving time to pre-heat mode 15 minutes (default)
    Recovery time from pre-heat mode 30 sec.
    Moving time to sleep mode 58 minutes (default) 58 minutes (Europe)
    * Printer mode: 10sec. (default)
    Recovery time from sleep mode 75cpm model: 53.25sec or less. 65cpm model: 48.15sec or less.
    Tags: default, mode, power, time
    • Phil B.
      Field Supervisor

      10,000+ Posts
      • Jul 2016
      • 22808
      #2
      Re: power problems concerning MX-7500

      Originally posted by dwarf
      we have a customer who experiences a lot of electrical power problems in their building...can somebody offer a recommendation for the proper type of voltage regulator we should steer them towards?... here is what the manual says about power requirements...

      200 V (North America, etc.) 200 V (Europe, etc.)
      Maximum rated power Consumption*1 2880W 3840W
      Energy consumption rate Not applicable
      TEC value (Measured result) 65cpm machine 8.1kWh Now Measuring
      75cpm machine 9.1kWh Now Measuring
      TEC value (Standard) Tier2 65cpm machine 20.5kWh (0.70kwh * 65 - 25.0 kwh)
      75cpm machine 27.5kWh (0.70kwh * 75 - 25.0 kwh)
      Network/Fax waiting power consumption: 1W or less
      * The network protocol is TCP/IP only.
      No
      Moving time to pre-heat mode 15 minutes (default)
      Recovery time from pre-heat mode 30 sec.
      Moving time to sleep mode 58 minutes (default) 58 minutes (Europe)
      * Printer mode: 10sec. (default)
      Recovery time from sleep mode 75cpm model: 53.25sec or less. 65cpm model: 48.15sec or less.
      try these folks

      AMETEK Electronic Systems Protection

        Comment

        • driving lots of miles
          Trusted Tech

          250+ Posts
          • Jun 2016
          • 378
          #3
          Re: power problems concerning MX-7500

          we use the Smart Power Systems and have had good results with them.
          smartpowersystems.com

            Comment

            • Phil B.
              Field Supervisor

              10,000+ Posts
              • Jul 2016
              • 22808
              #4
              Re: power problems concerning MX-7500

              Originally posted by driving lots of miles
              we use the Smart Power Systems and have had good results with them.
              smartpowersystems.com
              do they have a warranty against failure of their product and damage to the unit? 30a version carries up to $12,000 repair cost to the unit should their product fail.

                Comment

                • driving lots of miles
                  Trusted Tech

                  250+ Posts
                  • Jun 2016
                  • 378
                  #5
                  Re: power problems concerning MX-7500

                  Yes there is a warranty against failure of their product and damage to the unit, I don't have the exact numbers in front of me.

                    Comment

                    Previous template Next
                    Working...