Removing Saddle Stitch Stapler MX-FN10

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • mojorolla
    The Wolf

    2,500+ Posts
    • Jan 2010
    • 2583
    #1

    Removing Saddle Stitch Stapler MX-FN10

    Having done this a few time, not to mention the manual for this is not so great, I decided to snap a few shots along the way. I did not include covers as I feel if you cannot get the covers off, you have no business touching what is behind those covers.


    1. CONTROL BOARD CONNECTION.jpg2. HARNESS GROUND.jpg3. SS SIDE VIEW.jpg4. ALL THREE CLIPS INSTALLED.jpg5. SS-FRONT VIEW.jpg6. SS STAPLE UNIT FULL FRONT.jpg7. STAPLE UNIT FULL FRONT.jpg8. SS INSTALLED LOOSE BRACKET.jpg9. FIRST CLIP.jpg10. SECOND CLIP.jpg


    Failing to plan is planning to fail!!!
    Tags: None
    • mojorolla
      The Wolf

      2,500+ Posts
      • Jan 2010
      • 2583
      #2
      Re: Removing Saddle Stitch Stapler MX-FN10

      11. THIRD CLIP.jpg12.WHITE COVER INSTALLED.jpg13.. HARNESS GROUND2.jpg14. CONTROL BOARD CONNECTION2.jpg


      Failing to plan is planning to fail!!!

        Comment

        • bilyahn
          Service Manager

          1,000+ Posts
          • Dec 2006
          • 1470
          #3
          Re: Removing Saddle Stitch Stapler MX-FN10

          Removing it was a PITA but getting it lined up properly when you reinstall it is worse!!

            Comment

            • gwaddle
              Senior Tech

              500+ Posts
              • May 2009
              • 782
              #4
              Re: Removing Saddle Stitch Stapler MX-FN10

              So glad I found this thread. It helped a lot. Thank you. I really want to have the other guy in the shop put it back together because I sure don't want to. But I'm pretty sure he'd tell me where to stick it.
              I know I should be ashamed of myself. Strangely though, I am not.

                Comment

                • mojorolla
                  The Wolf

                  2,500+ Posts
                  • Jan 2010
                  • 2583
                  #5
                  Re: Removing Saddle Stitch Stapler MX-FN10

                  I hate this finisher. Loud, whiny, and the most awful drive design for a stapler I have possibly ever seen.

                  None the less, glad it helped.


                  Failing to plan is planning to fail!!!

                    Comment

                    • Vulkor
                      Senior Tech

                      500+ Posts
                      • Jun 2009
                      • 946
                      #6
                      Re: Removing Saddle Stitch Stapler MX-FN10

                      have a Feeling I'll be using this soon. Got one with a lot of FPPD3_N Jams.

                        Comment

                        • mojorolla
                          The Wolf

                          2,500+ Posts
                          • Jan 2010
                          • 2583
                          #7
                          Re: Removing Saddle Stitch Stapler MX-FN10

                          Try firmware first. Each engine has specific firmware for the FN10.


                          Failing to plan is planning to fail!!!

                            Comment

                            • CopierTechofOmens
                              Agitating Artificer

                              250+ Posts
                              • Jan 2009
                              • 268
                              #8
                              Re: Removing Saddle Stitch Stapler MX-FN10

                              I got called into the office after replacing this stapler the first time. I Forgot to align it the first time, made a nice noise. Then, when I was almost done the bearing dropped into stapler. By the third time I got pretty good at it...

                              "4 hours? On one call? Where were you really?"
                              sigpic

                                Comment

                                • mikez
                                  Technician

                                  Site Contributor
                                  • Oct 2012
                                  • 30
                                  #9
                                  Re: Removing Saddle Stitch Stapler MX-FN10

                                  I need to get the gears right above the motor. I can't find any in the parts manual. thanks.

                                    Comment

                                    Previous template Next
                                    Working...