TOSHIBA E-556 LCF JAMS

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • SOS
    Technician
    • Oct 2011
    • 46
    #1

    TOSHIBA E-556 LCF JAMS

    Hello, Anyone can help me, I have 3 toshiba e-556 machines, it always jams when we using LCF tray, we tried taking all paper LCF out, then other 2 trays work fine, I even update firmware, change rollers, and paper feed unit, still paper jams LCF, anyone know the problem help please
    Thanks
    Tags: None
    • blackcat4866
      Master Of The Obvious

      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22930
      #2
      Re: TOSHIBA E-556 LCF JAMS

      jam codes? =^..^=
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • SOS
          Technician
          • Oct 2011
          • 46
          #3
          Re: TOSHIBA E-556 LCF JAMS

          Yes, error code E5A0, E860, E010, E721
          Thank you very much

            Comment

            • blackcat4866
              Master Of The Obvious

              Site Contributor
              10,000+ Posts
              • Jul 2007
              • 22930
              #4
              Re: TOSHIBA E-556 LCF JAMS

              Here are a few possibilities:
              Misfeeds jam code E5A0, E010. (9) jammed pages are found in the fuser claws. Enduser is copying book originals, leaving a heavy black border. Combined with 1mm voids, the resulting copies jam in the fuser claws. Paper reaching the other side of the fuser roller blocks the thermistors, causing a minor meltdown. Replace upper fuser roller (melted plastic inside), white heater sheath, and any melted fuser claws. Perform image adjustments, specifically increasing the lead edge void to 4mm, and trail void to 3mm. Demonstrate use of the Edge Erase function when copying book originals.

              Misfeeds (E5A0) at the fuser exit. Also possible, streaks. Web motor does not run (during copying or 03-124:ON, 03-174:OFF). Pin connecter to red wire backs out of the connector, losing contact. Heat roller build up with toner when it isn't cleaned for 90K prints. Refit retracted pin into the connector.

              =^..^=
              If you'd like a serious answer to your request:
              1) demonstrate that you've read the manual
              2) demonstrate that you made some attempt to fix it.
              3) if you're going to ask about jams include the jam code.
              4) if you're going to ask about an error code include the error code.
              5) You are the person onsite. Only you can make observations.

              blackcat: Master Of The Obvious =^..^=

                Comment

                • bruce 49dcs
                  Trusted Tech

                  100+ Posts
                  • Jan 2017
                  • 140
                  #5
                  Re: TOSHIBA E-556 LCF JAMS

                  I have had this on a number of Toshiba lct for me its always been the rubber rollers on a shaft that are mounted on the lct access door become hard and slick you should be finding paper right there just starting to come in at the access door I use rubber rejouvinator of replace the rollers on the door also clean or replace the rollers in the lct that contact the ones on the door
                  well that's my 2 cents worth hope its that simple and nothing to complicated

                    Comment

                    Previous template Next
                    Working...