Toshiba e-studio 256se scanner and radf update failure

[Thomas007]

Re: Toshiba e-studio 256se scanner and radf update failure

this is why there is error to update RADF.

RADF UPDATE ERROR.pdf

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

I have the correct file. Maybe someone did, because as I posted before I saw the firmware installed was T169SLGWW.02 before I did my updating. I have .01N file. Please read the entire posts before posting. But thanks to all for the support. I have the download jig K-PWA-DLM-320 which I will try on later.

Sent from my GT-I9300 using Tapatalk

[drolfe@webmail.co.za]

Re: Toshiba e-studio 256se scanner and radf update failure

Recently I've just updated firmware for e356se yellow dot 4ccd type due to MFP not able to power OFF...Everything run out smoothly except the RADF update failed with error R13... Luckily it doesn't affect the MFP and the RADF is working...No idea what is going wrong...

[ATTACH=CONFIG]29830[/ATTACH]

I have attached the scrrenshot of the files for the firmware update if that helps any

[didi2005]

Re: Toshiba e-studio 256se scanner and radf update failure

Recently I've just updated firmware for e356se yellow dot 4ccd type due to MFP not able to power OFF...Everything run out smoothly except the RADF update failed with error R13... Luckily it doesn't affect the MFP and the RADF is working...No idea what is going wrong...

RADF_R13.jpg

[drolfe@webmail.co.za]

Re: Toshiba e-studio 256se scanner and radf update failure

the red dot is 3ccd firmware, can you make a print from the computer cause if you have updated the incorrect firmware it will make a print but wont make a copy. if so the only way to repair it is with the jig or contact the toshiba distributor and send them the scanner board and they will put the correct firmware on for you

if you have the T169SLGWW.02 firmware then you have the 4CCD which is wrong

[drolfe@webmail.co.za]

Re: Toshiba e-studio 256se scanner and radf update failure

Thnx. I will try that. But the biggest question in my mind was Why the installed version of scanner is .002 in the manual it should be .01N for red dot? and still there is no error f350?

Sent from my GT-I9300 using Tapatalk

the red dot is 3ccd firmware, can you make a print from the computer cause if you have updated the incorrect firmware it will make a print but wont make a copy. if so the only way to repair it is with the jig or contact the toshiba distributor and send them the scanner board and they will put the correct firmware on for you

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

Try to replace RAM

Thnx. I will try that. But the biggest question in my mind was Why the installed version of scanner is .002 in the manual it should be .01N for red dot? and still there is no error f350?

Sent from my GT-I9300 using Tapatalk

[Thomas007]

Re: Toshiba e-studio 256se scanner and radf update failure

Try to replace RAM

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

Yes. I read the technical bullettin.
The copier is Xenon lamp, Red dot 01N is attached on the SLG board.
The installed version of Scan firmware is T160SLGWW.002.
But theres no error unless I started copying. After the first page goes out, it will take sometime and error F111 pops out.

Yes. I tried 08-9090. Service Mode appeared in lower left side of the screen.but still the same behavior when I started copying.

Sent from my GT-I9300 using Tapatalk

[Thomas007]

Re: Toshiba e-studio 256se scanner and radf update failure

Do You read technical biuletyn?

Result if incorrectfirmware is installed F350 Error afterPWR ON!!!

You have F111!!!

Do you try 08-9090?

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

I think I know what seems to be the problem. Thank you for the technical bullettin. I checked the board it is 01N (red). The installed version is T160SLGWW.002. My file is 01N so I was thinking why the installed version is different. The updater version is not showing but I have the correct file. I asked the costumer and they said someone took the machine before for repair. Maybe they installed the wrong one. Is there anyway to reflash it without using the download jig?

Sent from my GT-I9300 using Tapatalk

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

Thanks Thomas007. I will try that later. By the way, in addition to that the scanner is just moving a little bit forward going to the slit glass and then going back to the home position. Its not even lighting. If will do 08-9090, do I have to calibrate the developer?

Sent from my GT-I9300 using Tapatalk

[Thomas007]

Re: Toshiba e-studio 256se scanner and radf update failure

For F111 try 08-9090

3CCD_4CCD.pdf

[didi2005]

[jobert]

Re: Toshiba e-studio 256se scanner and radf update failure

By the way, is the file name for the yellow one the same file name for the red dot?

Sent from my GT-I9300 using Tapatalk