Canon IR 105 and 105+ M2 and M3 Fiery Problem!

[Onetouch]

I have Canon IR 105+ M3 Fiery wich was working ok. But now when it's booting it says "Mismatch hardware problem shuting down in progres" and then goes to IDLE and then shuts itself down right after.

And for the Canon IR 105 M2 Fiery dose not establish connection with the copier. It say's connect Image Runner and EXIT.

Dose anyone have any idea about what's going on? (Both fierys seems like working okay, all the ligts are on when I connected with the copier and I did tried Inter-face from 1 to 4 but still ko luck).

[teckat]

I have Canon IR 105+ M3 Fiery wich was working ok. But now when it's booting it says "Mismatch hardware problem shuting down in progres" and then goes to IDLE and then shuts itself down right after.

And for the Canon IR 105 M2 Fiery dose not establish connection with the copier. It say's connect Image Runner and EXIT.

Dose anyone have any idea about what's going on? (Both fierys seems like working okay, all the ligts are on when I connected with the copier and I did tried Inter-face from 1 to 4 but still ko luck).

M2> Use a laptop computer to test the imageRUNNER, imagePASS M2 to laptop communication. (If the imagePASS M2 communicates in this setup then the problem may be with the customer's network. If it still does not ping continue to step three). 3. Flash the imageRUNNER to the latest system software.
4. Perform DC-CON, R-CON and MMI clear.


have u replaced the Video PCB Assembly recently ??
if so=When the Video PCB Assembly is replaced in the imagePASS L1 / M1 / M2 / M3, be sure to remove the security chip from the old board and put it on the new board.

on M3
Re-Set >/Copier / Option / Int-Face / IMG-CONT from 4 to 0,>Power Off, > Power On> Re-set> IMG-CONT back to 4 > and Power off then on.

[Onetouch]

I'll try and let you know tomorrow. I have Canon SST but I don't have system software and I counldn't find anywhere.
Thanks for the quick reply.

[Onetouch]

ImagePass M2 is working now. Thanks for the help Teckat.
But I still have the same problem with ImagePass M3 and I did the trouble shuting. I still get the message ""Mismatch hardware problem shuting down in progres" and then shuts itself down right after I see IDLE. I have service manual for M1 & M2 but I don't have for M3 and M1,2 dosen't mantion about such as error message. So, I don't really know about what's happining. I might need service manual for M3 and maybe system software to reinstall. I would really appreciated any help. motc77@hotmail.com

[teckat]

ImagePass M2 is working now. Thanks for the help Teckat.
But I still have the same problem with ImagePass M3 and I did the trouble shuting. I still get the message ""Mismatch hardware problem shuting down in progres" and then shuts itself down right after I see IDLE. I have service manual for M1 & M2 but I don't have for M3 and M1,2 dosen't mantion about such as error message. So, I don't really know about what's happining. I might need service manual for M3 and maybe system software to reinstall. I would really appreciated any help. motc77@hotmail.com

thanks, try this > completely disconnect on the M3 all cables & power cord / remove all M3 connections to 105+ shut down M3

go back and Select- Copier > Option > Int-Face > IMG-CONT- set it to 0 / power up 105+ without M3 connected to it/
go in to Copier > Option > Int-Face > IMG-CONT- set it to 4 / turn off 105+ > re- attach the M3 to 105+& Power all back up /
Hope for best

[Marcos RC]

[teckat]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

---

Hello! I have an Imagepass M2 connected to an IR105, I just can not get into setup mode to configure the IP address on it. I need to add the IP address to install the drivers on the network and on the computers to make the prints.
What is the procedure?
What are the keys that need to be pressed to enter the SETUP? Thanks for your attention and help!

================================================== ================================================== ===========================
imagePASS M2
IMG-CONT Setting: IMG-CONT Setting: 4


Enter service mode by hitting Additional Functions, 2 and 8 simultaneously, then Additional Functions. 2. Select COPIER.
3. Press Option from the tabs on the top of the LCD screen.
4. Select INT-FACE.
5. Press IMG-CONT. It will become highlighted.
6. Hit the number key desired (0, 1, 3, 4). The value will change to the number entered .
7. Press OK and then power cycle the copier.

Your lucky day !!!!!!!!!!!!!!!!!!!
Read manual link-------------------------


Dropbox - imagePASS-M2 Configuration Guide.pdf

[Marcos RC]

Image Cont: 01 e bootque as teclas sejam pressionadas , o modo de

[Phil B.]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

Image Cont: 01 e booting as teclas selecionadas estarem pressionadas, o modo de setup

Excuse me.. but not everyone here knows this language.... the site is run by english speaking folks and most techs here do also.. Please in the future post your requests/comments in English.. Thanks

[Marcos RC]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

I can not access the setup mode of Imagepass-M2. I can not access through the selection keys. The key sequence does not work when pressing for Network setup and TCP / IP configuration.
Thank you for your help!

[teckat]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

I can not access the setup mode of Imagepass-M2. I can not access through the selection keys. The key sequence does not work when pressing for Network setup and TCP / IP configuration.
Thank you for your help!

---

**Before attaching the imagePASS-M2 to an imageRUNNER-7200/8500/85/105.

In the service mode of the imageRUNNER, please make the following setting:
Copier>Option>INT-FACE>IMG-CONT to "4"

Power off Printer

Connect M2 Power Cord
Connect M2 to Printer (Copier interface cable )
Power up Printer
Power up M2

Now do the M2 Set up
Then Print Config Page







I

[Marcos RC]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

Thank you, friend, I was able to connect with your help!
I had long since stopped working as a technician, and I did not remember the procedure anymore.
MAY GOD BLESS YOU!

[teckat]

Re: Canon IR 105 and 105+ M2 and M3 Fiery Problem!

Thank you, friend, I was able to connect with your help!
I had long since stopped working as a technician, and I did not remember the procedure anymore.
MAY GOD BLESS YOU!

---

Thanks_Pizza Man .jpgwelcome