[Misc] IRC3220 Colour Adjustment

[abbas]

Pls HElp... Very Urgent...
I'm in a troublewith the colour adjustment of Canon IRC 3220 machine using service mode.
any pls help me...
its quite very urgent

pllsssss....pllsssss...

[hknwbec]

Here is one simple adjustment that you can try. Step 1 - Press * ( Additional Function ), Step 2- Select Auto Gradation Adjustment , Step 3 - Select Full Adjustment, And then you follow it instruction until Finished. It would be better if you attach the copy for reference.

[teckat]

Pls HElp... Very Urgent...
I'm in a troublewith the colour adjustment of Canon IRC 3220 machine using service mode.
any pls help me...
its quite very urgent

pllsssss....pllsssss...

if u have a Fiery connected/ use the Kodak gray scale/ procedure- under Printer tab

what are your Color image issues ??

color quality/blur/faded/missing color/light/dark/ ????

[SCREWTAPE]

If your values are off in service mode for your color, check out your service mode values from the door. There should be a couple of sheets behind the panel that's on your front door.
Do not make any adjustments for your color in service mode if your not quite sure about what your doing.

[teckat]

color-wheel-subt&#11.jpg

ADDED NOTE:
The tiny yellow dots that appear on documents produced by many color laser printers and copiers. These yellow dots form a coded pattern on every page the printer produces and can be used to identify specific details about a document; for example, the brand, model, and serial number of the device that printed it and when it was printed. In short, the printer dots are a surveillance tool that can link each printed page to the printer that printed it.

guide..JPG
Computer graphics software is used to overlay the black dots in the microscope image with larger yellow dots for greater visibility. iRC3200/3220 has yellow dots
spy-vs-spy_tofu_&#11.JPG

The top most row and left most column are a parity row and column for error correction. They help verify that the forensic information has been read accurately (and, if a single dot has been read incorrectly, to identify the location of the error). The rows and columns all have odd parity: that is, every column contains an odd number of dots, and every row (except the topmost row) contains an odd number of dots. If any row or column appears to contain an even number of dots, it has been read incorrectly.
Each column is read top-to-bottom as a single byte of seven bits (omitting the first parity bit); the bytes are then read right-to-left. The columns (which we have chosen to number from left to right) have the following meanings:

• 15: unknown (often zero; constant for each individual printer; may convey some non-user-visible fact about the printer's model or configuration)
• 14, 13, 12, 11: printer serial number in binary-coded-decimal, two digits per byte (constant for each individual printer; see below)
• 10: separator (typically all ones; does not appear to code information)
• 9: unused
• 8: year that page was printed (without century; 2005 is coded as 5)
• 7: month that page was printed
• 6: day that page was printed
• 5: hour that page was printed (may be UTC time zone, or may be set inaccurately within printer)
• 4, 3: unused
• 2: minute that page was printed
• 1: row parity bit (set to guarantee an odd number of dots present per row)

The printer serial number is a decimal number of six or eight digits; these digits are coded two at a time in columns 14, 13, 12, and 11 (or possibly just 13, 12, and 11); for instance, the serial number 00654321 would be coded with column values 00, 65, 43, and 21.

[SCREWTAPE]

I should've ask. Are you having registration issues. Are your colors not uniform.

[clc1000]

color registration problem

deassembly all 4 laser unit turn the lens mover motor gear to see start point at the hole on the motor install plate, then reassemly all 4 laser unit turn on copier make auto gradation full adjust

[teckat]

deassembly all 4 laser unit turn the lens mover motor gear to see start point at the hole on the motor install plate, then reassemly all 4 laser unit turn on copier make auto gradation full adjust

you are replying to a post that is over two months old
Head-Bang..JPG

[Kapten]

Clean the itb driveroller.
Take out the itb and clean the belt insida and the drive rollers.

[teckat]

Clean the itb driveroller.
Take out the itb and clean the belt insida and the drive rollers.

look at original post date/ over two months old> 5-09-2010

abbas has left the building/
ELVIS..jpg