[Error Code] Image Press C1 error code E000005

[COCODIAZ]

Hello someone can help with this issue. thanks

[teckat]

Hello someone can help with this issue. thanks

E000 0005
During warm-up after the fixing assembly jam, the temperature does not rise after the specified period of time (600 sec.
Reset in service mode: COPIER>FUNCTION>CLEAR>ERR

Remove and Inspect Fixing unit/ if it looks ok-put back/ clr error / report back

[hemai2005]

E000 0005
During warm-up after the fixing assembly jam, the temperature does not rise after the specified period of time (600 sec.
Reset in service mode: COPIER>FUNCTION>CLEAR>ERR

Remove and Inspect Fixing unit/ if it looks ok-put back/ clr error / report back

add to teckat
check fixing web

[COCODIAZ]

Thanks a lot, I clear the err, and now is working. Very useful

[teckat]

Thumbs up..jpg



Reminder **Web Error is E005 0000/0001
Best Bet is= Try a get a C1 Service Manual

[otreb]

i have the same error code i clear the errors still has problem replace sensor still not working any help.

[teckat]

i have the same error code i clear the errors still has problem replace sensor still not working any help.

when u can not clear a E000, U NEED TO REMOVE FIX UNIT TO INSPECT IT/ look for jammed paper inside/inspect heaters/thermistors
check for a thermistor open circuit/paper wrap


Fixing Method by lower fixing belt
Heater=inside fixing roller 2pc (main heater/sub heater; integrated type)
Inside inlet roller =1pc.
Inside outside heating roller = 1pc.


Control temperature

Fixing roller 165 deg C (standby)
Fixing belt (inlet roller) 95 deg C (standby)


Outside heating roller
200 deg C (standby)

Fixing temperature detection
Fixing roller Main thermistor THM1 (roller center; non-contact)
Sub thermistor THM2 (roller rear end; contact)
Inlet roller Main thermistor THM3 (roller center; contact)
Sub thermistor THM4 (roller rear end; contact)

Outside heating roller
Main thermistor THM5 (roller center; contact)
Sub thermistor THM6 (roller rear end; contact)

Fixing temperature control=
during warm-up, standby, printing, last rotation, power save mode

Fixing speed control
down sequence (black-and-white, constant velocity only)

Protective mechanism=

A check is run for the following to cut power to the heater in the event of a fault.
check on the temperature using the main/sub thermistor
cutting the supply power using the thermal switch

Fixing roller TP1 (roller front end; contact; operating temperature of 180 +/-7
deg C)
Fixing belt TP2 (roller center; non-contact; operating temperature of 130 +/-5
deg C)
Outside heating roller
TP3 (roller front end; contact; operating temperature of 220 +/-8
deg C)

check for a thermistor open circuit/paper wrap

Separation mechanism=

-Separation Roller
Separates paper from the fixing roller. Separates paper by pressing the separation roller of
which first diameter is 20 mm dia into the fixing roller to generate a local curvature change.
-Lower Separation Claw
Prevents wrapping of paper around the fixing belt (as when paper is curling downward)


Cleaning mechanism=

fixing roller by using the collecting roller and taking up the cleaning web
Fixing belt= none
outside heating roller =by the cleaning roller

Control mechanisms
- cleaning web drive control
- cleaning web length detection
- belt/web/outside heating roller attachment/detachment control
- belt displacement control


fix.JPG

[parsa]

cannot enter to service mode canon ir8500
i peress * 2&8 * in key canon ir8500 about not entr
why?????????????????
help meeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

[otreb]

hey is *28* the 28 together or the same time that should work

[teckat]

cannot enter to service mode canon ir8500
i peress * 2&8 * in key canon ir8500 about not entr
why?????????????????
help meeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

You should post under help for iR8500-

THIS POST WAS FOR A IMAGE PRESS C1 ISSUE