Kyocera M6030 Printing lines

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • neelsaraiya
    Junior Member
    • Nov 2020
    • 2
    #1

    [Misc] Kyocera M6030 Printing lines

    I had yellow and magenta vertical lines printing on the right hand size of each color print.

    So the geek in me decided to open it all up, clean up all the drums and reassemble it all together.

    Now its printing just lines . photos attached

    Imgur: The magic of the Internet
    Tags: clean, decided, lines, open, printing
    • Copierstud
      Technician
      • Nov 2019
      • 38
      #2
      Re: Kyocera M6030 Printing lines

      I have had this problem and was a bad black drum.

        Comment

        • blackcat4866
          Master Of The Obvious

          Site Contributor
          10,000+ Posts
          • Jul 2007
          • 22703
          #3
          Re: Kyocera M6030 Printing lines

          One of the developing units is arcing to the drum, via the developer spacers. The trick is determining which ones, without replacing all 8 units (drum and developing unit of whatever color).

          If the bars do not show on black images, you can rule out the black drum & developing units.

          Were I to take a wag, I'd say yellow is your color.

          Keep in mind that all the color drums are the same part, so you can use your new drum as C, M, or Y. But the developing units are different, specifically C, M, or Y.

          Does that make sense? =^..^=
          If you'd like a serious answer to your request:
          1) demonstrate that you've read the manual
          2) demonstrate that you made some attempt to fix it.
          3) if you're going to ask about jams include the jam code.
          4) if you're going to ask about an error code include the error code.
          5) You are the person onsite. Only you can make observations.

          blackcat: Master Of The Obvious =^..^=

            Comment

            • neelsaraiya
              Junior Member
              • Nov 2020
              • 2
              #4
              Re: Kyocera M6030 Printing lines

              @blackcat4866 - why do you think its the yellow?

                Comment

                • blackcat4866
                  Master Of The Obvious

                  Site Contributor
                  10,000+ Posts
                  • Jul 2007
                  • 22703
                  #5
                  Re: Kyocera M6030 Printing lines

                  When I've seen this issue on a wide variety of color Kyocera engines, the color that has the smallest, narrowest, or lightest color bars is usually the one causing the issue ... but not every time. Call it an educated hunch. =^..^=
                  If you'd like a serious answer to your request:
                  1) demonstrate that you've read the manual
                  2) demonstrate that you made some attempt to fix it.
                  3) if you're going to ask about jams include the jam code.
                  4) if you're going to ask about an error code include the error code.
                  5) You are the person onsite. Only you can make observations.

                  blackcat: Master Of The Obvious =^..^=

                    Comment

                    • KYO_OEM
                      Senior Tech

                      500+ Posts
                      • Aug 2011
                      • 636
                      #6
                      Re: Kyocera M6030 Printing lines

                      i agree with blackcat.
                      Seen several cases and mostly coming from yellow DV/DK
                      i think it would duplicated by the belt.
                      Please remember that yellow will be the first color which would transfered.
                      (count clockwise turning from belt)
                      If you print in bk, no colordrive for color DVs and no maincharging for color DKs

                        Comment

                        Previous template Next
                        Working...