Ricoh IM C300 SC672-02

[gilbert]

Hellow Techs
Please assist me i have IMC 300 which is not initializing.
only laser motors are running, it is coming ready but will not print
or copy once i command it to do so.It keeps on showing ""PROCESSING"'PRINTING"' until
Sc672-02 appears.I have tried another BICU and Controller board form another device
but error keeps coming.

[Gift]

Try another OP panel

[luca72]

Hellow Techs
Please assist me i have IMC 300 which is not initializing.
only laser motors are running, it is coming ready but will not print
or copy once i command it to do so.It keeps on showing ""PROCESSING"'PRINTING"' until
Sc672-02 appears.I have tried another BICU and Controller board form another device
but error keeps coming.

try to update the firmware, and to tighten a little the USB connectors of any cable that connects the panel to the board


metis usb ctr-op.jpg

[gilbert]

try to update the firmware, and to tighten a little the USB connectors of any cable that connects the panel to the board


metis usb ctr-op.jpg

I have managed to update firmware and checked the usb cable,the error has
changed to Sc670-02

[TonerMunkeh]

Make sure the toners are seated properly, this latest incarnation of the Griffin is just as annoying as it's older siblings for this.

[luca72]

I have managed to update firmware and checked the usb cable,the error has
changed to Sc670-02

probably, you are near to the solution, check that there are no hidden / disconnected connectors of the boards left, that you have tried to replace previously (it happens), and if you have the possibility try a "flying" usb cable, the psu could also be involved, android panel, is up to date ? .... here also speaks of "VODKA", but at this time it doesn't seem the case ... LOL!


SC670-02
The engine is off when the machine starts (it is possible to restart the SC) (* See "When SC670 is displayed" below)
Machine inactivity was detected after the ENGRDY signal was not confirmed.
• CPU reset from watchdog timer
• CPU reset by software
• CPU reset from CPU exception management
• Restore VODKA slave
• CPU recovery due to hardware / noise failure
• VODKA recovery due to hardware / noise failure
The motor board was unexpectedly reset.
Check if the SC error occurs by turning the machine off and on again at least 10 times. If the SC error occurs again, proceed as follows. Check if the SC error repeats by turning the machine off and on again after each stitch.
1. Reconnect the BiCU (PCB1) and the controller board (PCB24).
Error. To apply 見 出 し 1 to the text to be displayed here, use the tab
Home..Error. To apply 見 出 し 1 to the text to be displayed here, use the
Home tab.
615
No. Type Details (Symptom, Possible Causes, Troubleshooting Procedures)
2. Replace the card in the following priority.
1. BiCU (PCB1)
2. PSU (PCB16)
3. Controller board (PCB24)

[anothertech]

probably, you are near to the solution, check that there are no hidden / disconnected connectors of the boards left, that you have tried to replace previously (it happens), and if you have the possibility try a "flying" usb cable, the psu could also be involved, android panel, is up to date ? .... here also speaks of "VODKA", but at this time it doesn't seem the case ... LOL!


SC670-02
D
Il motore è spento quando la macchina si avvia (è possibile eseguire il riavvio dell’SC) (* Vedere "Quando viene visualizzato SC670" di seguito)
L'inattività della macchina è stata rilevata dopo che il segnale ENGRDY non è stato confermato.
• Ripristino della CPU da timer watchdog
• Ripristino CPU da software
• Ripristino CPU da gestione eccezione CPU
• Ripristino VODKA slave
• Ripristino della CPU dovuto a guasto hardware/rumore
• Ripristino VODKA dovuto a guasto hardware/rumore
La scheda motore è stata ripristinata inaspettatamente.
Controllare se l'errore SC si verifica spegnendo e riaccendendo la macchina almeno 10 volte. Se l'errore SC si verifica nuovamente, procedere come segue. Verificare se l'errore SC si ripete spegnendo e riaccendendo la macchina dopo ogni punto.
1. Ricollegare la BiCU (PCB1) e la scheda controller (PCB24).
Errore. Per applicare 見出し 1 al testo da visualizzare in questo punto, utilizzare la scheda
Home..Errore. Per applicare 見出し 1 al testo da visualizzare in questo punto, utilizzare la
scheda Home.
615
Nr. Tipo Dettagli (Sintomo, Possibili cause, Procedure di ricerca guasti)
2. Sostituire la scheda nella seguente priorità.
1. BiCU (PCB1)
2. PSU (PCB16)
3. Scheda controller (PCB24)

Look Man, we don't read Dutch here on this English board, and no I'm not translating it, maybe you could before you post it.

[luca72]

Look Man, we don't read Dutch here on this English board, and no I'm not translating it, maybe you could before you post it.

sorry! I messed with copy and paste

[slimslob]

Look Man, we don't read Dutch here on this English board, and no I'm not translating it, maybe you could before you post it.

Google translate is extremely easy to use. This is actually an international site with international membership.

[anothertech]

Google translate is extremely easy to use. This is actually an international site with international membership.

If I was going to post something on a site that used another language, I'd translate what I wrote into that language before posting, that way I'm the only one that has to translate it, instead of every person that wants to read it. Common sense, English board, post in English.