Activity Stream - Copytechnet.com

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Groups Groups

8 Minutes Ago

shaunt replied to a thread [Misc] Canon C5045 finisher removal in Canon

Thank you so much! I feel like an absolute idiot for not noticing this at all. That took all of 30 seconds. You're an absolute lifesaver!

2 replies | 87 view(s)

1 Hour Ago

CP-1015 replied to a thread Issue updating firmware C-308/C-368 per USB-stick (2GB) in Konica Minolta

I always use diskpart. But with "clean all".

30 replies | 590 view(s)

1 Hour Ago

EarthKmTech started a thread c3350i adf failing to bring pickup rollers back up in Konica Minolta

noticing this is a common theme in dusty environments. the reverse torsion clutch, the first one on the shaft after the main drive gear gets a...

0 replies | 23 view(s)

1 Hour Ago

TA_Tech started a thread [Misc] iR2530i not detecting Tray 2 in Canon

Hi everyone I know she's an old lady, but I've come across 2x iR2530's with low mileage for a very good price that I'm hoping to restore a bit and...

0 replies | 28 view(s)

1 Hour Ago

nikolai.aleksie replied to a thread Error 061-319 in Xerox

Error 061-319 and 061-343 - Customer Support Forum

8 replies | 365 view(s)

2 Hours Ago

copier addict replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

What are you calling a lie?

5101 replies | 6009382 view(s)

3 Hours Ago

Dech replied to a thread Error 061-319 in Xerox

Check your ribbon cables to the ros (lazer) unit.

8 replies | 365 view(s)

3 Hours Ago

slimslob replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

You know that is a lie. The truth is "the motive for the demands was nakedly political. The company had threatened to pack up its Montreal...

5101 replies | 6009382 view(s)

3 Hours Ago

slimslob replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

Canadian PM Justin Trudeau facing calls to resign because of a political influence scandal Wow shades of Quid Pro Quo Joe Biden pushing for the...

5101 replies | 6009382 view(s)

3 Hours Ago

Dech replied to a thread C60 code 093-317 in Xerox

If the toner is blocked, it blows F10 fuse on the iot Pwb and the toner motor sometimes burns its brushes. if this happens replace iot and motor......

5 replies | 444 view(s)

3 Hours Ago

Dech replied to a thread Xerox DC IV-C2263 error code 093-320 in Xerox

I've had( look at the attachment, no 9) a tooth break on the no 9(link guide assy) in attachment. Its a black slider shaft that engages the colour...

2 replies | 108 view(s)

4 Hours Ago

slimslob replied to a thread [Jamming] MP 501 funny jam codes in Ricoh, Savin, Gestetner, Lanier

The trouble shooting may say double feed for J031 but both codes are actually Lag jams, the trail edge it late leaving the sensor. Usual causes are...

1 replies | 66 view(s)

5 Hours Ago

copier addict replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

Okay, I'll play your part too. He pushed "Made in US" but has most of his merchandise made in China.

5101 replies | 6009382 view(s)

5 Hours Ago

copier addict replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

So, how do you feel about Cruz turning into a sniveling boot licker?

5101 replies | 6009382 view(s)

5 Hours Ago

BillyCarpenter replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

I have no idea what you're talking about because I don't follow Candian politics.

5101 replies | 6009382 view(s)

5 Hours Ago

slimslob replied to a thread Just how Crazy is Donald Trump! in Rants, Raves, and Everything Else

In the 2016b primary season Donald Trump was not my choice for President. He was a former Democrat and I did not trust him. My choice would have been...

5101 replies | 6009382 view(s)