Activity Stream - Copytechnet.com

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Groups Groups

1 Minute Ago

slimslob replied to a thread Latest on the Corona Virus in Rants, Raves, and Everything Else

Dr. Fauci warns US may not return to ‘normalcy’ until 2022

4760 replies | 301651 view(s)

5 Minutes Ago

slimslob replied to a thread Ricoh mp7500 strange problem, broken polygon motor ever 100k copies in Ricoh, Savin, Gestetner, Lanier

Are you absolutely positive that there were no Service Codes. It could be a Level C Service Code. SCs that are not shown on the operation panel. They...

14 replies | 243 view(s)

6 Minutes Ago

skynet replied to a thread Latest on the Corona Virus in Rants, Raves, and Everything Else

Has he actually said that on TV or is it reported that he suggested that. The press over here prints any garbage so so long as they claim "its...

4760 replies | 301651 view(s)

20 Minutes Ago

CP-1015 replied to a thread Konica Minolta Bizhub C454 falsely saying low Cyan but it's full & very light prints_ in Konica Minolta

Service Mode Imaging Process Adjustment Manual Toner Add But first I would like to see: State Confirmation Level History 1 Level History 2 ...

10 replies | 246 view(s)

45 Minutes Ago

m_donakov replied to a thread Ricoh mp7500 strange problem, broken polygon motor ever 100k copies in Ricoh, Savin, Gestetner, Lanier

I check that when i first time got that priblem, everting is ok, Problem is fixed for 100k when i put another polygon motor, but i cant figure what...

14 replies | 243 view(s)

2 Hours Ago

teckat replied to a thread Canon OID values in Canon

May help Canon Copiers - MIB monitoring - THWACK

1 replies | 81 view(s)

2 Hours Ago

Hansoon replied to a thread DK150 or DK170 in Kyocera

* Ahem * :) Hans

1 replies | 37 view(s)

2 Hours Ago

teckat replied to a thread [Error Code] IR Advance 6275 263-000 Error code in Canon

�� I believe CP is a check pin on the Board, could be a small depression or actual pin or something that looks like a small female plug. Look on...

1 replies | 49 view(s)

2 Hours Ago

femaster replied to a thread C224 Bizhub Bypass Tray and Tray 2 switched in Konica Minolta

Lets start out easy. Paper size in the regular trays is auto detected using sensors inside the copier and is based on the position of the paper...

1 replies | 41 view(s)

2 Hours Ago

hquang started a thread C224 Bizhub Bypass Tray and Tray 2 switched in Konica Minolta

Hi All, I am new to this group. I need some help from this group expertises. I don't remember what I did when trying to customize the banner...

1 replies | 41 view(s)

2 Hours Ago

femaster replied to a thread 72-87 FS-534 Folding unit in Konica Minolta

Where that paper is being pulled from, there should never have paper there. It should be going down into the slot that is on the right side of those...

11 replies | 294 view(s)

2 Hours Ago

BillyCarpenter replied to a thread 3551ci background problem in Kyocera Mita, Copystar

Yes, from a USB drive. I've yet to see a bulletproof copier. ;)

29 replies | 774 view(s)

2 Hours Ago

bronco31 replied to a thread 3551ci background problem in Kyocera Mita, Copystar

just print from a usb drive? Yes calibration huge mystery to many of us ! Also on my mind a question: Heres the latest Kyocera out in...

29 replies | 774 view(s)

2 Hours Ago

nicknt82 replied to a thread [CQ] Canon IRAC 5051 copy quailty just goes light in middle of printjob in Canon

I thinks you should replace whole of right door, not only transfer roller.

10 replies | 404 view(s)

3 Hours Ago

bronco31 replied to a thread Kyocera 2-series Question in Kyocera Mita, Copystar

OK thanks so much BC...:D Am i correct here? .. the 32xx is low speed model design.. (32ppm is top speed for that model) . and the 35xx is the...

22 replies | 591 view(s)

3 Hours Ago

nochick replied to a thread Xerox DC IV-C2263 error code 093-320 in Xerox

error code 093 is most I have found on site 100% from R1 area , toner all over that. just vacuum it until u can move gear easy with your hand. if...

3 replies | 151 view(s)

3 Hours Ago

Synthohol replied to a thread Bad network connection in Konica Minolta

Set the network speed to 100 speed duplex. I find most routers now autonegotiate the speed. Modern nic cards in copiers do the same. Sometimes...

2 replies | 70 view(s)

3 Hours Ago

allan replied to a thread Bad network connection in Konica Minolta

Does it have the latest and greatest firmware? Any CFA14 or CE301 in the history? Have you done self diagnostics on it?

2 replies | 70 view(s)

4 Hours Ago

Brian8506 replied to a thread iRA 6055 in Canon

Unfortunately too many people ask for help but then don’t reply when they’ve solved it or given up. It would be nice to get a follow up. Sent...

22 replies | 1798 view(s)