Activity Stream - Copytechnet.com

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Groups Groups

1 Minute Ago

allan replied to a thread [Error Code] Bizhub C280 error C2554 in Konica Minolta

Have you used DV610 before. Should work fine. Sounds like the dev unit is not resetting. Check under consumable life or in service mode if the unit...

16 replies | 7103 view(s)

2 Minutes Ago

Hansen88 replied to a thread H-codes MX-M4070 series in Sharp

I am one of the 75%that does not do this. I have not heard this before. I heard about turning off and back on before doing firmware. What does this...

5 replies | 184 view(s)

6 Minutes Ago

azehnali replied to a thread I need a good source in For Sale, Trade, or Wanted

what models?

3 replies | 570 view(s)

7 Minutes Ago

blackcat4866 replied to a thread [Jamming] PC417 Jams C650i in Konica Minolta

I think I'd focus on PS152, PS153, & PS158. I know it's a little different, but I came across these jams on a 654e. What I found on the 654e was...

3 replies | 122 view(s)

10 Minutes Ago

ThisPete replied to a thread 5053ci Adj lead edge void in Kyocera Mita, Copystar

I usually just use U415, that seems to be sufficient to stop most fuser wraps.

7 replies | 261 view(s)

24 Minutes Ago

emujo2 replied to a thread Konica Minolta Bizhub C227 - connection to Active Directory for user authentication in Konica Minolta

Here's what you should be doing..Every AD user has attributes..one of these attributes can be the ID card number..You will need to figure out what...

1 replies | 81 view(s)

24 Minutes Ago

kjg replied to a thread Kyocera M3540idn Jam 501 in Kyocera Mita, Copystar

Lots of responses on this one. I would agree to look at the clutch pack for feed. Replacement is not difficult. (was mentioned also - its a...

12 replies | 487 view(s)

28 Minutes Ago

SalesServiceGuy replied to a thread What is the best YouTube movie you found lately? in Rants, Raves, and Everything Else

OneRepublic - I Ain’t Worried (From “Top Gun: Maverick”) OneRepublic - I Ain’t Worried (From “Top Gun: Maverick”) - YouTube

972 replies | 452451 view(s)

30 Minutes Ago

luca72 replied to a thread Anyone know if the Fusor's Nip Pad has a part reference? in Ricoh, Savin, Gestetner, Lanier

to me they always look the same, however the loose parts can be found on alibaba or aliexpress if you want

9 replies | 307 view(s)

32 Minutes Ago

Gift replied to a thread [Jamming] PC417 Jams C650i in Konica Minolta

We had the most probs with the conveyance section - there's a modified spring available: Current Parts No. New Parts No.

3 replies | 122 view(s)

32 Minutes Ago

luca72 replied to a thread Anyone know if the Fusor's Nip Pad has a part reference? in Ricoh, Savin, Gestetner, Lanier

maybe you have put too silicone oil, or maybe you haven't waited long enough for it to absorb, then it must have come out slightly from the sides of...

9 replies | 307 view(s)

40 Minutes Ago

Abdo98 started a thread C300i latest firmware? in Konica Minolta

Would anyone be able to share with me the latest C300i firmware? Thank you!

0 replies | 24 view(s)

41 Minutes Ago

mojorolla replied to a thread H-codes MX-M4070 series in Sharp

If I had to guess, I would say 75% of tech miss this step on these machines. :)

5 replies | 184 view(s)

55 Minutes Ago

misganaw started a thread [Misc] Canon iR2425 How to Set up Remote Scan on Windows 10 in Canon

hello guys,Do you guys have canon ir2425 remote scanner driver. on company site i can only find generic driver which does not support scanning.

0 replies | 19 view(s)

56 Minutes Ago

LiamXCIII replied to a thread TA8353ci Belt Initialize error 33 in Kyocera Mita, Copystar

Hiya, Unfortunately the old belt unit has a rip in it :/ Part of the reason I have replaced the belt unit, but it's failing belt initialize. ...

2 replies | 74 view(s)

59 Minutes Ago

Gift replied to a thread Anyone know if the Fusor's Nip Pad has a part reference? in Ricoh, Savin, Gestetner, Lanier

Perhaps the internal heat shutters or it's mechanisms aren't properly in place? I remember these parts were hard to handle with just two hands and...

9 replies | 307 view(s)

1 Hour Ago

blackcat4866 replied to a thread TA8353ci Belt Initialize error 33 in Kyocera Mita, Copystar

If you re-install the old belt unit, does it pass the initialization? =^..^=

2 replies | 74 view(s)

1 Hour Ago

CHEBLA started a thread Ricoh pro c5100s with error sc 514 in Ricoh, Savin, Gestetner, Lanier

Hi everyone Since 2 months i'm fighting with sc 514 on my Ricoh. Machine show jams (but there's no paper) ,when i clear and close the drawer unit...

0 replies | 35 view(s)