View Full Version : Dead Machine C8000 cc101 code
beetle73
11-18-2016, 03:45 AM
Hi all
I have a KM C8000 with a CC101 code
Customer had power issues resulting in this code
Replaced OACB,PRCB,Memoory control bd,2 PS units ,and Nvram from a working machine
Instant code , machine will not boot
Any ideas?
Thx
mx6turbo89
11-18-2016, 04:48 AM
You can try a Main image processing board (IPB/M). That's supposed to be one of two possible faulty components (the other is the PRCB which you've already replaced).
beetle73
11-18-2016, 12:47 PM
Hi
I appreciate the reply but according to the svce manual possible causes are PRCB and OACB which have both been replaced.
DigiMan
11-18-2016, 04:43 PM
Check your boards for fuses blowing out(even with the new boards)
mx6turbo89
11-18-2016, 05:28 PM
Hi
I appreciate the reply but according to the svce manual possible causes are PRCB and OACB which have both been replaced.
Right you are, sorry, I looked up the wrong code.
As Digiman says, check fuses and voltage points. Here's an ICP list that might help: https://www.dropbox.com/s/5ikktxabjtq9fc0/%28bizhubPRESS%20C8000%29ICP_list_ver.1.1%28EN%29_ G.pdf?dl=0
Check out ICP23 on the PRCB for 5V.
907tec
11-18-2016, 07:52 PM
I have heard that "recalling standard data" (found under Machine Adjustment) can help with this code, but it has not worked for me in the past. A few months ago I had a C7000 throwing this code, ended up replacing the PRCB and Color Reg/Gamma assembly. Have you looked at the "Troubleshooting Guide" at the end of the service manuals? There is a section in there related to C-C101 codes immediately upon startup - caused by pinched/grounded wiring in the vertical conveyance system.
Either way, I would start by checking continuity across all the ICP's on the PRCB (both old board and new board).
beetle73
11-19-2016, 03:19 PM
Thx for the info
We did find a blown fuse on the Prcb but have since replaced bd.
Currently ohming out wiring harnesses
Quatro
11-19-2016, 05:36 PM
Hi,
What is the previous status of the machine before the error occurred?
Try to check the voltage supplied on OACB and PRCB if there is 5V,12V and 24V.
Good Luck.:o:o:o
beetle73
11-20-2016, 03:00 AM
Machine was working fine on the Friday.
Monday morning machine had CC101 code when powered up!
Fans are on but no pre-drive at all
DigiMan
11-22-2016, 09:01 AM
If it keeps blowing it even if you replaced it you can try(although its not reccomended for obvious reasons)shorting it.
beetle73
11-23-2016, 04:36 AM
Not a bad idea.
Still blowing fuse on the PRCB board.
Wiring harness on order.
beetle73
09-16-2017, 10:32 PM
Thx for all the ideas.
Nothing worked.
Customer upgraded!
Peterzhao
09-17-2017, 03:24 PM
Hi all
I have a KM C8000 with a CC101 code
Customer had power issues resulting in this code
Replaced OACB,PRCB,Memoory control bd,2 PS units ,and Nvram from a working machine
Instant code , machine will not boot
Any ideas?
Thx
Please check the power first before you do anything. I have one experence, the customer use two 110V brake to make the 220V power for Konica, later one brake cut off, the machine give us the same code.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.