View Full Version : Error Code C6500 EROR CODE C2720
liondor1969
02-01-2017, 08:14 AM
Haloo
Plese hepl my,i have C6500,after code error J3201 i recive code eror C2720..mesage contact service,the C6500 pawer off.I lost al info on print contor..that happens when catch paperboard in C6500..
Thanks
liondor1969
02-02-2017, 07:42 PM
Haloo
Plese hepl my,i have C6500,after code error J3201 i recive code eror C2720..mesage contact service,the C6500 pawer off.I lost al info on print contor..that happens when catch paperboard in C6500..
Thanks
Hallo plese help my with this error code
EROR CODE C2720
Synthohol
02-02-2017, 10:02 PM
High voltage unit/2 (HV/2)
Second transfer roller
When the second transfer was
ON, second transfer abnormality
detection signal was continuously detected for the specified
time.
check the HV wire from the back of the xfer roller assy.
put a strip of black electrical tape over the guide plate on top of the factory one.
make sure the ground spring clip contacts the front of the roller well.
liondor1969
02-03-2017, 04:16 PM
High voltage unit/2 (HV/2)
Second transfer roller
When the second transfer was
ON, second transfer abnormality
detection signal was continuously detected for the specified
time.
check the HV wire from the back of the xfer roller assy.
put a strip of black electrical tape over the guide plate on top of the factory one.
make sure the ground spring clip contacts the front of the roller well.
Ok,i must to control this ..thanks
Texers
02-08-2017, 03:35 PM
Ok,i must to control this ..thanks
if that didn't solve your code, replace the power block on the transfer assy.. A1DUR73300.
liondor1969
02-09-2017, 08:57 AM
if that didn't solve your code, replace the power block on the transfer assy.. A1DUR73300.
Thanks,naw I have a red line on print,including non printing area
Texers
02-09-2017, 01:10 PM
Thanks,naw I have a red line on print,including non printing area
Magenta Drum?
liondor1969
02-09-2017, 04:25 PM
Magenta Drum?
Yes,magenta drum,I change magenta drum with cyan..than cyan have problems with blue line but in left side..on magenta the same drum make magenta line in left side :-)
tulintron
02-17-2017, 07:39 PM
Hallo plese help my with this error code
EROR CODE C2720
I found in the field, another technician changed the 2nd transfer electric poles with discharge guide in the bottom of the ADU, under the 2nd transfer.
After correcting the error, defect is over.
liondor1969
02-18-2017, 06:09 AM
I have this problem only when using drawer 5..big ..a technician says it's a firmware problem. wen i use paper drawer 1-2-3 and i have paper jam..everything clean and start ok..than wan i have paper jam on drawer 4-5 after i clean all,i become this error cod C2720.I want to try to do firmware updates..if you have other suggestions.
Thanks
lartis.aineias
01-18-2021, 08:27 PM
I had this problem in konica C6000 and finally the problem was in the up 2nd transfer holder. it was cracked at the point where it gets current!4789747898
Στάλθηκε από το SM-G975F μου χρησιμοποιώντας Tapatalk
Phil B.
01-18-2021, 08:41 PM
I had this problem in konica C6000 and finally the problem was in the up 2nd transfer holder. it was cracked at the point where it gets current!4789747898
Στάλθηκε από το SM-G975F μου χρησιμοποιώντας Tapatalk
4 year dead thread...
allan
01-18-2021, 10:56 PM
4 year dead thread...
Hehe just adds to the thread. Who knows who will search for this next.
Robin (ACS Collective)
12-20-2021, 08:14 PM
Hehe just adds to the thread. Who knows who will search for this next.
Yeah me :p
Any news on this error? I got C6000 and I am constantly getting c2720. I checked and cleaned the roller but nothing. Getting magenta lines on the roller so changed drum but still everything as it was...
EDIT:
lol - just gave my last try, changed the roller and everything goes xD
cheers everyone
TEST10
12-21-2021, 05:31 AM
[QUOTE = Phil B.; 1664839] Hilo muerto de 4 aņos ... [/ QUOTE]
I resolved in the same way!:frio:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.