Bizhub 240f, firmware

[Hansoon]

Anyone able to send me the firmware for the KonicaMinolta 240f please? Machine is stuck on the KonicaMinolta logo and doesn't continue booting. Seems I need FW:

MB-750 Firmware version B9A0A0
OP-700 Firmware Version A5A0A0
Konica Minolta 240f Firmware Version D4A0A0

Thanks

Hans

[copyman]

Are you sure about that model #? I don't see it listed on the K/M dealer site. Perhaps it is only sold in Europe?

[allan]

Wow what is that?
37879

[Hansoon]

Its originally a Muratec which is being sold in Europe as Bizhub-240f.

Would the firmware only be available on the Europe Website??

Hans

[copier tech]

Dont see these little boxes very often.

Here's the FW.


https://mega.nz/#!BdkSjaJR!CDT90aLO8ttl6AT1qVX0D2buetMLCwh3NBhMOOx 07TY

[allan]

RICOH 1515 in the blood.

[Hansoon]

Dont see these little boxes very often.

Here's the FW.


https://mega.nz/#!BdkSjaJR!CDT90aLO8ttl6AT1qVX0D2buetMLCwh3NBhMOOx 07TY




Got it. Thank you very much.

BTW: Wish you guys would get rid of that Brexit.......

Hans

[Hansoon]

RICOH 1515 in the blood.

Don't think so Allan. Its basically a Muratec 2550. Even its Webinterface is showing "Muratec"

Hans

[Hansoon]

Until now I was able to revive the little beast two times with installing the firmware. Now it is not even accepting that anymore. The progress bar hangs in the last 10%. Machine is in a very hard to reach location, 7 stairs to climb, otherwise I would have replaced since long.

Any ideas? I have another working scrap machine to cannibalize for boards....... or better use it as Boat Anchor?

Hans

[Toxic]

I had one restarting problem (boot loop) on 240f and solve with replacing cf card from other scrap machine and it works.
Do not know is that your problem but just a hint.
What firmware version you have now?
You tried few different usb memory for firmware upload?

[Hansoon]

I had one restarting problem (boot loop) on 240f and solve with replacing cf card from other scrap machine and it works.
Do not know is that your problem but just a hint.
What firmware version you have now?
You tried few different usb memory for firmware upload?

Changed the CF-Card and machine came up. However there was an error message "501" firmware not matching. Tried to update the FW on that CF-Card from the scrap machine but it says "NG"

The firmware available to me is:

240f_EUR_D0A0A0_update.bin
240fEUR_Ver.txt

and

FWUD.bin
MB750_Ver.txt

I use a 2GB USB Stick

Any help please?

Hans

[Toxic]

About the 501 error,it could be different firmware version on current machine and donor machine cf card.
Check and match all 3 fw versions 240f,MB750,OP700
Try to get cf card back to donor machine and update firmware to be the same versions as on the other machine and try then replacing cf card again.
When you get NG during did you check error code ? (The datailed errror code will be displayed when you press <Setting>, <*>, <9>, <8>.)
If not try to disconnect lan cable before firmware update.
Also try manual mode method fw update if auto not working.

[Hansoon]

The little creep is back on his feet. Changed the CF-Card and updated the firmware once again but now more careful than the 1st time....... :o

Thanks for your help guys.

BTW: I have following FW, are these the latest & greatest, or is there "better" ?

240f_EUR_D0A0A0 and
MB750_B9A0A0
But unfortunately not the PCL OP700_EN

;)

Hans

[Xthedev]

PLEASE the mega link provided is no longer working and i need the firmware file. Anybody...please

[mbr002]

Is anybody able to send me the firmware for the KonicaMinolta 240f please? The machine shows the logo and stops with MB system error 12500. At CF card is written MB-750 - B3A0A0, before failure the machine reported


Main 240f EUR E4A0A0
Network MB750 C9A0A0
PCL OP700 EN B1A0A0


It seems to be a problem in network section, the checksum is missing.




Thank you
Martin

[Phil B.]

Is anybody able to send me the firmware for the KonicaMinolta 240f please? The machine shows the logo and stops with MB system error 12500. At CF card is written MB-750 - B3A0A0, before failure the machine reported
Main 240f EUR E4A0A0
Network MB750 C9A0A0
PCL OP700 EN B1A0A0
It seems to be a problem in network section, the checksum is missing.
Thank you
Martin
FYI CONTRIBUTORS to CTN get a quicker response to such requests.. https://www.copytechnet.com/forums/vbdonate.php?do=donate

[Phil B.]

PLEASE the mega link provided is no longer working and i need the firmware file. Anybody...please


FYI CONTRIBUTORS to CTN get a quicker response to such requests.. https://www.copytechnet.com/forums/vbdonate.php?do=donate

that link was from 2017.. of course it is no longer any good.

[mbr002]

FYI CONTRIBUTORS to CTN get a quicker response to such requests.. https://www.copytechnet.com/forums/vbdonate.php?do=donate

O.K., it's not a problem to support the forum, but I have to be sure that the firmware files will help me at least a little

[copier tech]

O.K., it's not a problem to support the forum, but I have to be sure that the firmware files will help me at least a little

We can supply you with the latest firmware however it's not a guaranteed fix, you could have a failed controller board.

Firmware Update - Printer & Copier Firmware (http://www.copierfirmware.co.uk)

[Toxic]

O.K., it's not a problem to support the forum, but I have to be sure that the firmware files will help me at least a little
In that case you are at wrong place.
If you call KM official tech guy to solve problem (for labour fee of course) maybe he will give you some sort of guarantee.

[tsbservice]

In that case you are at wrong place.
If you call KM official tech guy to solve problem (for labour fee of course) maybe he will give you some sort of guarantee.

😆 Toxic
So true my friend 👍

[BillyCarpenter]

He said he wants a guarantee. lol

Dude, you're killing me. I can't stop laughing. Stop it. :p

[Synthohol]

https://media1.tenor.com/images/48792794e92c448a4b75c50c0ad56a4e/tenor.gif?itemid=10492850

[tsbservice]

https://media1.tenor.com/images/48792794e92c448a4b75c50c0ad56a4e/tenor.gif?itemid=10492850

Hilarious :D

[mbr002]

In that case you are at wrong place.
If you call KM official tech guy to solve problem (for labour fee of course) maybe he will give you some sort of guarantee.

It's a sad finding - I supposed the forum is for users to help each other. Is it all really just about money? And as write "copier tech" maybe is bad the controller board. That's why I don't want pay the fw before try.


The copier is not for bussiness, it is only for using in our basic school. We got it as a gift from a office and it was good for two years. We can call KM official tech guy of course, but it not good idea, the machine is old.


If anybody want to help me, you can send me a PM. Thanks


Martin

[BillyCarpenter]

It's a sad finding - I supposed the forum is for users to help each other. Is it all really just about money? And as write "copier tech" maybe is bad the controller board. That's why I don't want pay the fw before try.


The copier is not for bussiness, it is only for using in our basic school. We got it as a gift from a office and it was good for two years. We can call KM official tech guy of course, but it not good idea, the machine is old.


If anybody want to help me, you can send me a PM. Thanks


Martin

I've seen plenty of end users receive help on here. Only my opinion but I don't think making a $10 contribution is much to ask. The techs here on this site don't get any of that money. If they do, I want my cut. :D

Seriously tho, people come on here all the time wanting something for free. Can 't have that...

Disclaimer: In no way am I saying you'll get what you want with a donation. Only that you may have a better chance.