View Full Version : Bizhub 754e
Gina82
11-15-2018, 08:32 PM
I have a bizhub 754e giving me a jam code in cassette 4. There was paper behind the 4th paper cassette, but it was removed and all the paper was retrieved. The machine is still saying there is a jam but gives no error code and it was trouble reset multiple times but the message still appears.
Phil B.
11-15-2018, 08:59 PM
I have a bizhub 754e giving me a jam code in cassette 4. There was paper behind the 4th paper cassette, but it was removed and all the paper was retrieved. The machine is still saying there is a jam but gives no error code and it was trouble reset multiple times but the message still appears.
print out the error code sheet.... it might be logged there... sounds like you might have a sensor out of place or defective.
have you run sensor test in SM?
Page counts on replaceable parts?
Have you cleaned out the sensors?
Gina82
11-15-2018, 09:20 PM
Which sensor would you think it might be. I have examined the paper feed unit, but I don't see anything out of place. How would I print the error code sheet on this machine?
Phil B.
11-15-2018, 09:34 PM
Which sensor would you think it might be. I have examined the paper feed unit, but I don't see anything out of place. How would I print the error code sheet on this machine?
RTFM
Gina82
11-15-2018, 09:51 PM
Can you clarify on the abbreviation RTFM
Phil B.
11-15-2018, 10:06 PM
Can you clarify on the abbreviation RTFM
READ THE FRIGGING MANUAL
Gina82
11-15-2018, 10:16 PM
READ THE FRIGGING MANUAL
Very helpful.
blackcat4866
11-15-2018, 10:51 PM
Did you mention a jam code? I don't think so. =^..^=
Woxner
11-16-2018, 12:54 AM
might have blown paper feed board. this happened on earlier series
cycle66
11-16-2018, 01:35 AM
Try checking the connector on the back of the tray, sometimes paper will get stuffed inside the connector and cause this.
D_L_P
11-16-2018, 01:46 AM
..The machine is still saying there is a jam but gives no error code and it was trouble reset multiple times but the message still appears.
I know your code is for tray 4 but check the reg roller auxiliary guide. There's a reflective mirror in the center just below the cleaning pad. It should be cleaned every call however, paper dust gets on in and it will show a jam after trouble resets and looking everywhere else.
Gina82
11-16-2018, 02:29 PM
Did you mention a jam code? I don't think so. =^..^=
There was no code given just a jam indication warning
Gina82
11-16-2018, 02:30 PM
I know your code is for tray 4 but check the reg roller auxiliary guide. There's a reflective mirror in the center just below the cleaning pad. It should be cleaned every call however, paper dust gets on in and it will show a jam after trouble resets and looking everywhere else.
I'll try that today and let you all know what result I get.
Synthohol
11-16-2018, 03:23 PM
if no code given, just look in svc mode in counters.
antone
11-16-2018, 06:13 PM
Do a trouble reset..with tray 4 pulled out!
Sent from my SM-N950U using Tapatalk
Gina82
11-27-2018, 02:30 PM
Update...Problem fixed. It was the connector. Reseated & problem solved! Thanks for everyone's help. Hope everyone had a Happy Thanksgiving & Merry Christmas.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.